Connect the Air Source Hose to the Air Plug (41). Note: If you are not using an automatic oiler system on your air compressor, before operation, add a few drops of Pneumatic Tool Oil to the airline connection. Remove the air line at the inlet and put 2 or 3 drops of good quality air tool oil into the air fitting each day of use. With heavy, prolonged use, do this at least twice a day. 2. Set the air pressure on your compressor to 60-125 PSI. Do not exceed the maximum air pressure of 125 PSI. Not

See Figure 1. Operating the Nailer 1. Attach the Nailer to the air supply at the Air Inlet (22). Start your compressor and check the pressure making sure it is set at the recommended 90 PSI and not to go over the maximum 90 PSI. 2. To fire, place the nose of the Nailer on the workpiece. The Nailer should not fire if the nose is not depressed. Once depressed, gently and briefly squeeze the Trigger (42) once. Do not fire repeatedly. Pins could bounce off of one another, damaging the work piece or

It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. Indicates a hazardous situation which, if not avoided, will result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. Addresses practices not related to personal injury. Symbol Propert

2. While doing this step and the next, hold the Nailer pointed away from you and any other people or fragile objects. Pull the Quick Release Lever (49) forward to the position shown in Figure 2. Remove the Driver Guide Cover (51). 3. Remove the jammed nail. Pliers may be necessary to remove a stuck nail. 4. Inspect the Drive Pin (46) for bends or breakage -see location in Figure 3. If it is damaged, do not use the tool until it is repaired by a qualified technician. 5. Lightly oil the Drive Pin

For technical questions and replacement parts, please call 1-800-444-3353 Specifications Air Inlet 1/4 ”-18 NPT Recommended Air Pressure 60 -100 PSI, 100 PSI Max. Magazine Capacity 100 Nails or 80 Staples Safety Feature Single Sequential Safety Trip Mechanism Nail Size .039-.042” Shank (18 Gauge), 5/8 ” -11/ 4 ” L Staple Size 1/4 ” Crown, .039-.042” Shank (18 Gauge), 1/2 ” -11/ 4 ” L Accessories Oil Dropper, 2 Wrenches, 1 Coupler Plug Save This Manual You will need the manual for the safety warn

TO PREVENT SERIOUS INJURY: Do not adjust or tamper with any control or component in a way not specifically explained within this manual. Improper adjustment can result in tool failure or other serious hazards. 1. WARNING! Even though the Nailer should be empty during this procedure, ALWAYS point the Nailer at a piece of scrap wood when testing. 2. Make sure the tool is disconnected from its air supply. 3. Completely empty the Magazine (71) of Nails. 4. The Nailer should not fire if the Nose Safe

SKU 41209 For technical questions, please call 1-800-444-3353. Page 5 Unpacking Unpacking Operation For best service, you should incorporate an oiler, regulator, and inline filter, as shown in the diagram below. Hoses, couplers, oilers, regulators, and filters are all available at Harbor Freight Tools. TO ROOFING NAILER Note: To connect this tool, we recommend you use the included quick connector. For smoother operation and to extend the life-span of the tool, put 3-5 drops of pneumatic tool oil

reach of children and other untrained persons. A tool is dangerous in the hands of untrained users. Maintain the tool with care. f. A properly maintained tool is more efficient and reduces the risk of binding and is easier to control. Check for misalignment or bindg. ing of moving parts, breakage of parts, and any other condition that affects the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. There is a risk of bursting if

(See Figure B.) LOADING COIL NAILS WARNING: Always wear ANSI approved impact safety goggles when reloading or performing any other maintenance on this tool. Other people in the work area must also wear ANSI approved impact safety goggles. WARNING! Make sure the Nailer is not attached to the air hose when loading the tool. 1. To open the Magazine Cover (91), press down on the Latch (57) and swing the Door (32) open. Then, swing the Magazine Cover open. (See Figure C.) MAGAZINE COVER (91) LATCH (5

Always release any built-up air even after disconnecting hose. Disconnect the Nailer when not in use. 11. Remove adjusting keys and wrenches. Check that keys and adjusting wrenches are removed from the tool or machine work surface before attaching to an air source. 12. Avoid unintentional starting. Be sure the trigger is in the Off position when not in use and before plugging in. Do not carry any tool with your finger on the trigger, whether it is attached to an air source or not. Do not point t