Assessments - 1, GPA: 4 ( )

Fabricante : Alliance Laundry Systems Arquivo Tamanho: 129.06 kb Arquivo Nome : a14bcc24-c076-4bb6-98a9-4ddf0768f3b0.pdf Língua de Ensino:

• In an area where it will come in contact with curtains, drapes, or anything that will obstruct the flow of combustion and ventilation air. • On carpet. Floor must be solid with a maximum slope of 1inch (2.54 cm). Installation in Recess or Closet: • A dryer installed in a bedroom, bathroom, recess or closet, must be exhausted outdoors. • Your dryer needs the space around it for proper ventilation. • A minimum of 120 square inches (774.2 square cm) of opening, equally divided at the top and bottom of the door, is required. Air openings are required to be unobstructed when a door is installed. A louvered door with equivalent air openings for the full length of the door is acceptable. ROUGH-IN DIMENSIONS 16 GDZ22-1 manual 10/22/01 11:45 AM Page 18 English Installation in Mobile Home • Dryer must be exhausted outside (outdoors, not beneath the mobile home) using metal ducting that will not support combustion. Metal ducting must be 4 inches (10.16 cm) in diameter with no obstructions. Rigid metal duct is preferred. • If dryer is exhausted through the floor and area beneath the mobile home is enclosed, the exhaust system must terminate outside the enclosure with the termination securely fastened to the mobile home structure. • Refer to previous pages for other important venting requirements. • Installation must conform to current Manufactured Home Construction & Safety Standard (which is a Federal Regulation Title 24 CFR-Part 32-80) or when such standard is not applicable, with American National Standard for Mobile Homes. Warning: The dryer is designed under ANSI z 21.5.1 for home use only. DO DON’T Correct Incorrect DO DON’T Correct Incorrect DO DON’T Correct Incorrect 17 GDZ22-1 manual 10/22/01 11:45 AM Page 19 English Electrical Connections Requirements and Instructions WARNINGS The following are specific requirements for proper and safe instructions can create electrical shock and/or fire hazard. electrical installation of your dryer. Failure to follow these 1. This appliance must be properly grounded. Electrical shock can result if the dryer is not properly grounded. Follow the instructions in this manual for proper grounding. 2. Do not use an extension cord with this dryer. Some extension cords are not designed to withstand the amounts of electrical current this dryer utilizes and can melt, creating electric shock and/or fire hazard. Locate the dryer within reach of the receptacle for the length power cord to be purchased, allowing some slack in the cord. Refer to the electrical requirements in this manual for the proper power cord to be purchased. 3. A U.L. approved strain relief must be installed onto power cord. If the strain relief is not attached, the cord can be pulled out of the dryer and can be cut by any movement of the cord, resulting in electrical shock. 4. Do not use an aluminum wire receptacle with copper wired power cord and plug (or vice versa). A chemical reaction occurs between copper and aluminum and can cause electrical shorts. The proper wiring and receptacle is a copper wired power cord with a copper wired receptacle. Note: Dryers operating on 208 Volt power supply will have longer drying times than operating on 240 Volt power supply. Danger: Improper connection of the equipment grounding conductor can result in a risk of electrical shock. Check with a licensed electrician if you are in doubt as to whether the appliance is properly grounded. The dryer must be connected to a grounded metal, permanent wiring system, or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance. 18 GDZ22-1 manual 10/22/01 11:45 AM Page 20 English 3-Wire Cord Connections green ground screw green neutral ground wire silver terminal nut tighten nut to these threads power cord strain relief mounting bracket 1. Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer upper corner. 2. Install a U.L. approved strain reli...

Baixe o seu

Para fazer o download, introduza 2 dígitos :