Assessments - 4, GPA: 4.3 ( )

Fabricante : Frigidaire Arquivo Tamanho: 1.42 mb Arquivo Nome : 917420EN.pdf Língua de Ensino:

You can use this function to activate or deactivate the sound. THE ANTICREASE FUNCTION Extends anticrease phase (30 minutes) at the end of the drying cycle to 90 minutes. This function prevents laundry from creases. Laundry can be removed during the anticrease phase. THE DELAY START FUNCTION Let to delay the start of a drying programme from minimum of 30 minutes to maximum of 20 hours. 1. Set the drying programme and functions. 2. Push the Delay start button again and again until the necessary time of the delay come into the view on the display (e.g. if the programme has to start after 12 hours.) 3. To activate the Delay start function, push the Start/Pause button. The time to start decreases on the display. 12 • clean the filter STARTING A PROGRAMME • drain the water container (See chapter CARE AND CLEANING.) To activate the programme push the Start/Pause button. The LED above the push button changes the color to red. CHANGE A PROGRAMME To change a programme, turn the programme selector to Stop and then set the programme again. CHILD LOCK FUNCTION The child lock can be set to prevent the children to play with the appliance. The child lock function locks all push buttons and the programme dial (this function does not lock On/Off button). To activate the child lock function push the Anti- crease and Delay Start buttons at the same time until the symbol come into view on the display. To deactivate push again the above buttons until the symbol go out of view. You can activate the child lock function: • before you push the Start/Pause button -the appliance cannot start • after you push the Start/Pause button all the push buttons and the programme dial are deactivated AT THE END OF PROGRAMME When the drying cycle is completed, the symbol flashes on the display. If the Buzzer function is on, an acoustic signal sounds intermittently for one minute. To remove the laundry: 1. Push the On/Off button for 2 seconds to deactivate the appliance. 2. Open the appliance door. 3. Remove the laundry. 4. Close the appliance door. After each drying cycle: ENGLISH 13 HINTS AND TIPS ECOLOGICAL HINTS • Do not use fabric softener to wash and then dry. In the tumble dryer laundry becomes soft automatically. • Use the condensate as distilled water, e.g. for steam ironing. If necessary clean the condensate before (e.g. with a coffee filter) to remove possible small pieces of fluff. • Always keep the airflow slots on the bottom of the appliance clear. • Use the load volumes specified in the programmes chapter. • Make sure that is good airflow in the appliance installation position. • Clean the filter after each drying cycle. • Spin good the laundry before drying. WATER HARDNESS AND CONDUCTIVITY Water hardness can be different for different locations. Water hardness has an effect on the water conductivity and the operation of the conductivity sensor in the appliance. If you know the value of the water conductivity you can adjust the sensor to dry with the better results. To change the sensor conductivity: 1. Turn the programme dial to available programme. 2. Push at the same time the Delicate and Anticrease buttons and hold down until one of the these symbols go into view on the display: – low conductivity <300 .S/ cm – moderate conductivity 300-600 .S/cm – high conductivity >600 .S/ cm 3. Push the Start Pause button again and again until you set necessary level. 4. To memorise setting push at the same time the Delicate and Anti- crease buttons. WATER CONTAINER FULL — INDICATION By default the indication LED is always on. It comes into the view at the end of the cycle or when the water container is full. When you use an external equipment to drain the container, the LED can be off. To activate or deactivate the indication: 1. Turn the programme dial to available programme. 2. Push at the same time the Delicate and Delay Start buttons and hold down until you see the correct setting: – the LED is off and the symbol goes into the view - The LED is permanently off – the LED is on and the symbol goes into the view - The LED is activated 14 CARE AND CLEANING The filter collects the fluff. The fluff occurs while the cloths are At the end of each cycle the filter LED is dried in the tumble dryer. on to tell you that the filter must be cleaned. CLEANING THE FILTER To clean the filter: 1. Open the door. 2. Pull the filter. 3. Open the filter. 4. Use a moist hand to clean the filter. 5. If necessary clean the filter with warm water using a brush. Close the filter. 6. Remove fluff from the filter socket. For this a vacuum cleaner can be used. 7. Put the filter inside the filter socket. CAUTION! Do not operate the tumble dryer without the filter or with damaged or blocked filter. Clean the filter after each drying cycle. Clogged filter increases the cycle time and causes higher energy consumption. DRAINING THE CONDENSED WATER CONTAINER Drain the condensed water container after each drying cycle. If the condensed water contain...

Baixe o seu

Para fazer o download, introduza 2 dígitos :