Assessments - , GPA: ( )

Instruções de Operação Electrolux, Modelo 137018200 A

Fabricante : Electrolux
Arquivo Tamanho: 2.83 mb
Arquivo Nome :

Língua de Ensino:

O documento está colocado, por favor, espere

Baixe o seu Fechar

O documento está colocado, por favor, espere

Baixe o seu Fechar

Momentarily turn on COLD supply and run some water into a bucket or container to clear any contaminants in the line. 4. Remove hose kit from dryer drum and inspect hose couplings for proper placement of rubber washers. 16 Installation Instructions Water connection, con’t (Steam Model only) WATER INLET ON DRYER DIRECT CONNECTION OR WITH EXTENSION COLD WATER SUPPLY HOSE TO WASHER If your installation has room for the COLD 1. watersupplytoacceptthe“Y”connectordirectly,threadthe“Y”connectortotheCOLDwater supply and snug it by hand; then tighten it another 2/3 turn with pliers. NOTE Ifyouwereabletoinstallthe“Y”connectordirectlyto the COLD water supply, please skip to step 8. Ifthereisnotroomtoinstallthe“Y”connector2. directly,threadtheshortextensionhoseontothe COLD water supply and snug it by hand; then tighten it another 2/3 turn with pliers. Threadthe“Y”connectortotheshort3. extensionhoseandsnugitbyhand;thentighten it another 2/3 turn with pliers. Connect the COLD inlet hose for the washer4. tothe“Y”connectorandsnugitbyhand;thentighten it another 2/3 turn with pliers. Connect the straight end of the long hose from 5. thekittotheotheroutletonthe“Y”connectorand snug it by hand. Connect the hose’s 90° coupling to the brass water inlet on the back of the dryer and snug it by hand. Tighten each connection of the dryer inlet hose another 2/3 turn with pliers. Turn on the water and check for leaks at all 6. connections. 16 Installation Instructions Water connection, con’t (Steam Model only) WATER INLET ON DRYER DIRECT CONNECTION OR WITH EXTENSION COLD WATER SUPPLY HOSE TO WASHER If your installation has room for the COLD 1. watersupplytoacceptthe“Y”connectordirectly,threadthe“Y”connectortotheCOLDwater supply and snug it by hand; then tighten it another 2/3 turn with pliers. NOTE Ifyouwereabletoinstallthe“Y”connectordirectlyto the COLD water supply, please skip to step 8. Ifthereisnotroomtoinstallthe“Y”connector2. directly,threadtheshortextensionhoseontothe COLD water supply and snug it by hand; then tighten it another 2/3 turn with pliers. Threadthe“Y”connectortotheshort3. extensionhoseandsnugitbyhand;thentighten it another 2/3 turn with pliers. Connect the COLD inlet hose for the washer4. tothe“Y”connectorandsnugitbyhand;thentighten it another 2/3 turn with pliers. Connect the straight end of the long hose from 5. thekittotheotheroutletonthe“Y”connectorand snug it by hand. Connect the hose’s 90° coupling to the brass water inlet on the back of the dryer and snug it by hand. Tighten each connection of the dryer inlet hose another 2/3 turn with pliers. Turn on the water and check for leaks at all 6. connections. Installation Instructions General installation 1. Connect the exhaust duct to the outside exhaust system (see pages 5 through 7). Use of a 4” (10.2 cm) clamp is recommended to connect the dryer to the exhaust vent system. Use metal foil tape to seal all other joints. 2. Carefully slide the dryer to its final position. Adjust one or more of the legs until the dryer is resting solidly on all four legs. Place a level on top of the dryer. The dryer MUST be level and resting solidly on all four legs. Rock alternating corners to check for stability. Remove and discard door tape. IMPORTANT Be sure the power is off at a circuit breaker/fuse box before plugging the power cord into an outlet. 3. Plug the power cord into a grounded outlet. 4. Turn on the power at the circuit breaker/fuse box. 5. Read the Use & Care Guide provided with the dryer. It contains valuable and helpful information that will save you time and money. 6. See the next page about performing a brief, helpful “Installation Cycle” for your new dryer. 7. If you have any questions during initial operation, please review the “Avoid Service Checklist” in your Use & Care Guide before calling for service. 8. Place these instructions in a location near the dryer for future reference. Grounding type wall receptacle Do not, under any circumstances, cut, remove, or bypass the grounding prong. Power cord with 17 NOTE A wiring diagram and technical data sheet are located inside the dryer console. 3-prong grounded plug 18 Installation Instructions WARNING FIRE HAZARD Before operating the dryer, make sure the dryer area is clear and free of combustible materials, gasoline, and other flammable vapors. Also see that nothing (such as boxes, clothing, etc.) obstructs the flow of combustion and ventilation air. Performing Installation Cycle NOTE On gas dryers, before the burner will light, it is necessary for the gas line to be bled of air. If the burner does not light within 45 seconds the first time the dryer is turned on, the safety switch will shut the burner off. If this happens, press cancel and wait 5 minutes before making another attempt to light. If your dryer has this console: 1.Empty the dryer drum. 2.After you plug in the dryer the first time: wake up the dryer by pressing any button, rotate cycle knob to touch up cycle, press the start button and then the can...