Assessments - 1, GPA: 3
(
)
)
|
Facilidade de uso
If this happens, turn the timer to "OFF" and wait 5 minutes before making another attempt to light. 7. Placethese instructions in a location near the dryer for future reference. NOTE: A wiring diagram is located inside the dryer. Lint Blade Retaining Pin Location and Orientation / Install the pins after the lint blade is installed. METER CASE INSRUCTIONS COIN BOX ADJUSTMENT The tight fit of the money box is set at the factory. Customer may loosen fit as desired by loosening the slotted nuts. See FIG.1. FIGURE Keep A record of all coin-box key numbers. A lost key can only be replaced by ordering the key numbers from the place were the unit was purchased. The key number is located both on the key and behind the end panel of the coin box. If the key number is not available, the lock must be drilled out to remove the coin box. 9 REPLACING NYLON TIMING CAMS ON ACCUMULATOR MECHANISM Electrical Shock Hazard • Disconnect both power supply cords from the electric power supply before making these changes. Change timing cams before completing electrical connection. Failure to do so could result in electrical shock or personal injury. A. Remove meter-case service door: 1. Loosen two screws securing timer bracket to meter case and lift timer assembly out. See FIG. 2 FIGURE 2 B. Remove nylon timing cam: 1. Rotate cam by hand until "V" notch lines up underneath the ratchet tooth. See FIG. 3. 2. Insert narrow screwdriver under nylon cam close to the timer shaft. Lift cam gently off shaft. Make sure that pressure is directed upward and the "V" notch clears the ratchet tooth. Timing Cam Pin Chart NUMBER TIME PER NUMBER TIME PER OF PINS COIN INSERTED OF PINS COIN INSERTED 1 180 minutes 7 25.7 2 90 8 22.5 3 6O 9 20 4 45 10 18 5 36 11 16.3 6 3O 12 15 INSTRUCTIONS FOR CHANGING VEND PRICE TOOLS NEEDED • Medium sized slotted screwdriver • Small slotted Phillips screwdriver Placeallscrewsandotheritemsremovedfrom coinslideassembly on a cloth so they will not get lost. STEP1 Remove slide mechanism from meter case (see FUGURE1). FIGURE 1 STEP2 Remove the coin slide extension from coin slide by removing two mounting screws and spacers (see FIGURE2). (2) Mounting Screws C, Replace new timing cam: 1. Besure drive lug isin place. Placecam (hub down) over timer shaft, lining up fiat on shaft with fiat of drive lug hole. 2. Rotate cam until "V" notch lines up with ratchet tooth. 3. Pressdown to seat cam on timer shaft, make sure that "V" notch freely clears ratchet tooth. Slide Return Spring STEP3 Remove coin sfide from coin chute: • Unhook and remove the coin slide return spring (see FIGURE2). • Turn coin slide mechanism upside down. • Remove coin slide stop by taking out two screws to the chute bottom (see FIGURE3). (2) SI G_ 10 * Pull coin slide out of coin chute (see FIGURE4). FIGURE 4 STEP4 Turn coin slide upside down and remove screw that holds coin receiver block (see FIGURE5). (1) Receiver Block Screw \ Spare Parts FIGURE 5 Compartment and Screw STEP5 Remove coin receiver block from coin slide (see FIGURE 6): * Turn coin slide right side up. Keep coin receiver block in place with your fingers. * Carefully lift coin slide from coin receiver block. If necessary, shake coin slide gently to loosen block. STEP 6 Set new vend price by adding or removing the appropriate block-out keys and/or dime inserts according to th Table of Vend Prices (see FIGURE7). NOTE: Black colored slots are closed off by block-out key. FIGURE 7 TABLE OF VEND PRICE COiN SLOTS 12345678 1|1|1|| | D|||||| | DDmmmm| | ||rl|||| | ufrl|||| | DD[]|||| | || rill|| | | D|rlrl||| | DDD[]||| | ||rlrlrl|| | D|rlrlrl|| | U D[][][]|| | || rlrlrlrl| | D|DDD[]| | DDDDDD| | |DDDDD| | D | rlrlrlrlrl | DD[] [][][][] | | rlrlrlrlrlrl | Drlrlrlrlrlrl | DDD[] [][][][] | rlrlI]rlrlrl I1 U 11[]I][]rl[] rl rlrlrlrlrlrlrl D VEND PRICE o $.10 $.20 $.2s $.3s $.4s $.so $.so $.70 $.7s $.8s $.9s $1.00 $1.1o $1.2o $1.2s $1.3s $1.4s $1.so $1.so $1.7o $1.75 $1.8s $2.00 FIGURE 6 11 To remove block-out keys, pull straight up. STEP7 NOTE: Be sure block-out keys and/or dime inserts are seated properly and ratchet dog is in place with its spring connected (see FIGURE8). Be sure the proper coin sizing block is in place. Ratchet Dog and Block-Out Keys FIGURE8 Change coin sizing block: • Remove two screws that hold upper coin chute cover. Remove cover (see FIGURE9). Anti-Cheat (2) Upper Coin Chute Cover Ga te Block Screws (2) Coin Sizing_ Coin Sizing FIGURE 10 ; Block Remove two screws that hold coin sizing block to upper coin chute cover cover (see FIGURE10). Put new coin sizing block in place. Reinsert and tighten mounting screws. Replace coin chute cover. Reinsert and tighten screws. Replace coin receiver block into sfide: Hold coin receiver right side up in the palm of one hand. Lower coin slide until coin receiver block fits into the coin slide cavity. CAUTION: Do not dislodge ratchet dog and spring. Hold coin receiver block in place with your fingers and turn slide upside down. Insert and tighten s...
Este manual também é adequado para os modelos :Secadores - 134313400 (2.69 mb)
Secadores - 134316200 (2.69 mb)