Assessments - 6, GPA: 3.8
(
)
)
|
Facilidade de uso
Problem solving guide Problem Possible cause Remedy The tumble dryer fails to start when switched on. No obvious cause. – Is the dryer switched on – Is the plug correctly inserted into the socket and switched on – Is the door closed properly – Has the fuse or circuit breaker tripped The interior drum lighting does not come on. The lighting switches off automatically (to save energy). Switch the dryer off and then on again. The lamp needs changing. Change the lamp as described at the end of this section. Problem solving guide Changing the lamp Disconnect the tumble dryer from the mains electricity supply. ^ Open the door. You will find the interior lamp cover at the top of the drum aperture. The lamp specification and maximum wattage is stated on the data plate and on the lamp cover. ^ Replace the lamp. ^ To close the cover push it upwards and press it on the left and right until you hear it click into position. ,Ensure that it is fitted into position securely, as any moisture could cause a short circuit. ^ Insert a suitable tool, such as a wide bladed screwdriver, under the side edge of the lamp cover as illustrated. ^ Apply a little pressure and whilst doing so turn your wrist in the direction of the arrow to open the cover. The cover will open downwards. The temperature resistant lamp should only be ordered from your Miele Dealer or the Miele Spare Parts Department. After sales service Repairs In the event of any faults which you cannot remedy yourself, or if the machine is under guarantee, please contact – Your Miele dealer, or – the Miele Service Department (see back cover for contact details). When contacting the your Dealer or the Service Department, please quote the model and serial number of your machine, both of which are shown on the data plate (visible when the door is opened). Future updates (PC) The indicator light marked PC is the interface used by Miele service technicians during service work for testing purposes and for updating the machine's programme data. Guarantee Please see the guarantee card supplied with your machine. Optional accessories Optional accessories for this dryer are available from your Miele Dealer or from the Miele Spare Parts Department. Please note that telephone calls may be monitored and recorded for training purposes. Front view aMains connection cable bControl panel cCondensed water container dDoor eService panel for condenser unit fFour height adjustable screw feet gAir inlet and outlet vent for cooling the condenser unit hExternal drainage options (e.g. via wash basin, wash basin drain outlet or gully) Installation and connection 35 Installation and connection Rear view Installation site a Protruding lid for holding when moving the machine (see arrows) b Air inlet vent for cooling the condenser unit c Mains connection cable d External drainage of the condensed water e Accessories for connection to a sink drain outlet ,The machine lid must not be removed. The dryer can be pushed under a worktop with its lid in place, providing the worktop is high enough. ,Make sure the dryer door can be opened without hindrance after installation. Transporting the machine to its installation site When moving the machine, you can hold it by the lid where it protrudes to the rear of the dryer. To manoeuvre the dryer out of its packing case to its installation site you will also need to hold it by the front feet. Washer-dryer stack The tumble dryer can also be combined with a Miele washing machine in a washer-dryer stack. The appropriate "WTV" stacking kit (available to order) to match your dryer is required. ,Stacking kits must only be installed by a suitably qualified fitter. Installation and connection Levelling the machine The machine must be perfectly level to ensure safe and proper operation. ^The screw feet can be adjusted to compensate for any unevenness in the floor. ,The air inlet and outlet vents on the front and back of the machine must not be covered as this would prevent sufficient ventilation for cooling the condenser unit. Room ventilation The air which is taken in when the dryer is in operation is blown out of the vents on the front of the machine and warms up the air in the room. It is very important, particulary if the room is small, to ensure adequate ventilation. Opening a window, for example, will allow more air to enter the room. Otherwise running times and energy consumption could be increased. Before moving the machine again (e.g. when moving house) After each use a small quantity of condensed water will collect in the area around the pump. This water can run out if the machine is tipped up when it is being moved. It is a good idea to run the Cool air programme for approximately 1 minute before moving the machine. Any remaining condensed water will then be fed into the condensed water container or out through the drain hose. Installation and connection External condensed water outlet General notes When drying is in progress, condensed water is pumped into the ...