Resultant de la Proposition californienne 65, ce produit contient des produits chimiques dont l’etat de la Californie reconnait causer le cancer et des anomalies congenitales ou d’autre danger pour la reproduction. • 1 • General SAFETY PrecauTIONs 1. The following safety information is provided as a guideline to help you operate your new welder under the safest possible conditions. Any equipment that uses electrical power can be potentially dangerous to use when safety or safe handling instructi

FUME HAZARDS 1.5 WARNING: FUMES, GASES, AND VAPORS CAN CAUSE DISCOMFORT, ILLNESS, AND DEATH! To reduce risk of discomfort, illness, or death, read, understand, and follow the following safety instructions. In addition, make certain that anyone else that uses this welding equipment or is a bystander in the welding area, understands and follows these safety instructions as well. Do not weld in an area until it is checked for adequate ventilation as • described in ANSI standard #Z49.1. If ventilati

It also performs general scratch start DC TIG. The Champion 10,000 offers a “no-nonsense” warranty. The engine is warranted separately by the engine manufacturer. Comes complete with 15 ft Work Cable and Clamp, and 20 ft Welding Lead and Electrode Holder! FEATURES BENEFITS You get a generator andwelder for about what you would pay for just a generator! Smooth arc starts with minimal “sticking”. Extraordinary motor starting characteristics. Strong continuous rating to run compressors, pumps, ligh

If there is any doubt, do not operate the tool. 18. Pacemaker safety warning. People with pacemakers should consult with their physician(s) before using this product; operation of equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker. 19. Use proper size and type extension cord. If an extension cord is required, it must be of the proper size and type to supply the correct current to the tool without heating up. Otherwise, the extension cord could

3. Insert the Handle (4) into the Handle Sockets (3) and mount the Handle Sockets to the Side Panel B (1) top using supplied hardware. Note: The Handle (4) configuration may differ slightly than what is shown in this manual. 4. Lift Side Panel B (1) all the way to expose the wire spool and Wire Feed Mechanism (11). Wire Feed Mechanism (11)Wire SpoolWire Spool Axle (10) Side Panel B (1) (C) (D) (34) – + 5. Remove the Nut from the Wire Spool Axle (10). Place the Wire Spool over the Axle with the w

With the OHV design, automatic idle and 10 gallon fuel tank, you can expect to put in long hours before having to stop and refuel. For example: • Welding at 125 amps, 100% duty cycle, uses about 1 gal of fuel every hour. • While not welding, the engine drops to idle speed using about 1/2 gal of fuel every hour. • On a typical job using 1/8-in 7018 electrodes (125 amps, 20% duty cycle) you can expect over 16 hours of operation. • Under a continuous load of 4,000 watts of auxiliary power, the Cham

Standard for Fire Prevention During Welding, Cutting, and Other Hot Work, norme NFPA 51B, de la National Fire Protection Association, P.O. Box 9101, 1 Battery March Park, Quincy, MA 02269.9101 (telephone : (617) 770.3000, site Web : et OSHA, Occupational Safety and Health Standards for General Industry, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q, and Part 1926, Subpart J, de l’U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 152

2-2. Manufacturer’s Rating Label For CE Products S-181 265-A EN 60974-1 X 100% 35% 16A/86V 27A/90V U0 = 255V I2 16A 27A U2 86V 90V IP 23 50 Hz1 I1max = 34AU1 = 115V I1max = 17AU1 230V I1eff = 20.5A I1eff = 10.2A 1 2-3. Symbols And Definitions A Amperes Plasma Arc Cutting (PAC) Adjust Air/Gas Pressure Low Air Pressure Light V Volts Increase No . Do Not Do This Temperature Protective Earth (Ground) Single Phase Constant Current Voltage Input On Off Percent Direct Current U0 Rated No Load Voltage (

106730 Rev A1 April 2006 April 2006 Technical Publications Genie Industries has endeavored to deliver the highest degree of accuracy possible. However, continuous improvement of our products is a Genie policy. Therefore, product specifications are subject to change without notice. Readers are encouraged to notify Genie of errors and send in suggestions for improvement. All communications will be carefully considered for future printings of this and all other manuals. Contact Us: e-mail: te

Built on the enduring and trusted foundation of the NA-5 controller and the innovations of the new Power Feed 10M wire feeder, the Power Feed 10A Controller is the next generation in automatic submerged arc feeding. Designed for use with the Power Wave AC/DC 1000 power source, the Power Feed 10A eliminates the need for a separate AC and DC controller, making this powerful hard automation system controllable, adaptable and easy to use. The user-friendly control panel offers a single-point of cont