Log:
Assessments - 3, GPA: 4 ( )

Instruções de Operação Hitachi, Modelo WS-55517

Fabricante : Hitachi
Arquivo Tamanho: 4.19 mb
Arquivo Nome : 3d2f00a9-3a87-41a3-b459-195cfa286ab5.pdf
Língua de Ensino: en
Ir para baixar



Facilidade de uso


See Connection Helpful Hints, at the end of this chapter for additional information on device setup. Connecting a Wall Outlet Cable or Cable Box Wall Outlet Cable (can be used with a CableCARD™) Figure 1 It is very important to connect the incoming cable for your primary viewing source to ANT-1, especially for CableCARD™ use. 1. Connect the primary incoming coaxial lead cable to ANT-1 MAIN on the TV back panel. 2. For an optional secondary antenna source, connect an antenna (or cable) to ANT-2 AUX. 3. If you have subscribed to a CableCARD™ service, the CableCARD can now be inserted into the CableCARD SLOT. Using a phillips screwdriver, remove the CableCARD cover screws. Insert the CableCARD, then replace the cover and screws. If you need more information regarding this service, please contact your cable service provider. DIGIT E1394 T/OUTPUT AUDIO ANT-2 AUX ANT-1 MAIN CableCARDTM SLOT – (DTV/CABLE /VHF/UHF) – E1 94 T/T OUTPUT 1. 2. TV back panel (section detail) Optional Secondary Antenna or Cable Primary Wall Outlet Cable 3. CableCARDTM SLOT (cover removed) DIGITATT L AUDIO Figure 1. Wall Outlet Cable Additional connection cables are not provided with the TV. They are available at most electronic stores. IMPORTANT Cable Box (compatible with PIP/POP) Figure 2 3 coaxial cables and one two-way RF splitter are required. These are not included with the TV. It is very important to connect the incoming cable for your primary viewing source to ANT-1, especially for CableCARD™ use. 1. Connect the incoming cable to IN on an RF splitter. 2. Connect one coaxial cable from OUT on the RF splitter to ANT-1 MAIN on the TV back panel. 3. Connect one coaxial cable from OUT on the RF splitter to IN on the cable box. 4. Connect one coaxial cable from OUT on the cable box to ANT-2 AUX on the TV back panel. Figure 2. Connecting a Cable Box Cable Box back panel section IN DIGIT AUDIO ANT-2 AUX ANT-1 MAIN CableCARD – (DTV/CABLE /VHF/UHF) – IncomingCable UT OUT DIGITATT L AUDIO CableCARD SLOT IN OUT OUT TWO WAY SPLITTER 1. 2. 2. 3. 3. 4. 4. TV back panel (section detail) Note: NetCommand® will assume that your Cable Box is connected as shown above. Also, that Channel 3 is the default output channel for the cable box. If either the connections or output channel are different, use the Change option of Edit NetCommand to apply the changes. Connecting a Single Analog Antenna or Separate UHF and VHF Antennas Single Antenna (not for use with CableCARD™) Figure 3 A 300-Ohm to 75-Ohm transformer is required. This is not included with the TV. For antennas with twin flat lead 1. For antenna with twin flat leads, connect the 300-Ohm twin leads to the 300-Ohm to 75-Ohm transformer. 2. Push the 75-Ohm side of the transformer onto ANT-1 MAIN on the TV back panel. For antennas with coaxial lead 3. Connect the coaxial lead directly to ANT-1 MAIN on the TV back panel. DIGIT AUDIO CableCARDTM 1 OUTPUT -ANT-1 MAIN – (DTV/CABLE /VHF/UHF) – DIGITATT L AUDIO CableCARDTM SLOT 300-Ohm FlatTwin Lead Optional 300-Ohm to 75-Ohm Matching Transformer 75-Ohm Coaxial Cable TV back panel (section detail) 3. 2. 1. ANTTT 2 AUX Figure 3. Connecting an Antenna Separate UHF and VHF Antennas Figure 4 A UHF/VHF combiner is required. This is not included with the TV. 1. Connect the UHF and VHF antenna leads to the UHF/VHF combiner. 2. Push the combiner onto ANT-1 MAIN on the TV back panel. External Antenna or Cable Back Side Flat Twin Lead UHF Antenna (Channels 14-69) VHF Antenna (Channels 2-13) 300 Ohm to 75 Ohm Combiner Flat Twin Lead UHF VHF TV back panel (section detail) ICE POR IEEE1394 INPUT/OUTPUT DIGIT AUDIOSERVICE PORT IEEE1 394 INPUT/OUTPUT -2 ANT-1 MAIN – (DTV/CABLE /VHF/UHF) – DIGITATT L AUDIO CableCARD SLOT 1. 2. ANTTT 2 AUX Figure 4. Connecting separate UHF and VHF Antennas Mitsubishi strongly recommends against using antennas with twin flat leads. Twin flat lead antenna wires are subject to interference which may adversely affect the performance of the TV. We recommend using coaxial antenna cable. 17 Connecting VCR Video and Audio to an Antenna or Wall Outlet Cable VCR to Antenna or Wall Outlet Cable Figure 5 A two-way RF splitter, 3 coaxial cables, right and left audio cables and S-Video or Video cables are required. These are not included with the TV. 1. Connect the incoming cable or Antenna to IN on the RF splitter. 2. Connect one coaxial cable from OUT on the RF splitter to ANTENNA IN on the VCR back panel. 3. Connect one coaxial cable from OUT on the RF splitter to ANT-1 MAIN on the TV back panel. 4. To use the TV speakers with the VCR, connect a set of audio cables from AUDIO OUT on the VCR back panel to INPUT 1 AUDIO-LEFT (MONO) and AUDIO-RIGHT on the TV back panel. The red cable connects to the R (right) channel and the white cable connects to the L (left) channel. If your VCR is mono (non-stereo), connect only the white (left) cable. CableCARDTM SLOT S-VIDEO VIDEO AUDIOLEFT/ (MONO) AUDIORIGHT INPUT 1 2 AUDIO 2 OT/ O) OT DVI Digita Digita S-Video ...

Este manual também é adequado para os modelos :
TV - WS-55517 (4.19 mb)
TV - WS-55517 (4.19 mb)
TV - WS-65517 (4.19 mb)
TV - WS-73517 (4.19 mb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias