Assessments - 4, GPA: 4 ( )

Fabricante : Hitachi Arquivo Tamanho: 4.19 mb Arquivo Nome : Língua de Ensino:

However, moving the TV, the TV’s location in relation to the Earth’s magnetic poles, and the passage of time can cause these adjustments to change. As a special feature, you have the ability to adjust the red and blue light beams in reference to the fixed green light beam. This process is called convergence. There are two separate memories for convergence. One, for SD 480i/480p signals; the other for HD 1080i signals. SD convergence should be adjusted while watching an SD source and HD convergence should be adjusted while watching an HD source. The TV should be fully warmed up before adjusting Convergence. Turn the TV On and wait at least 30 minutes before starting adjustments. Setup Menu, continued Convergence, continued Figure 10 When the Red and Blue crosshairs are properly converged, the center-screen crosshairs will appear white. You can press ADJUST , , or to move the Red and Blue crosshairs. Press VIDEO to switch between Red and Blue. Press AUDIO for the Advanced Convergence screen. Red Press ADJUST to converge the lines. Press VIDEO to switch from Red to Blue. Press MENU to go back. Press CANCEL to delete changes. Press AUDIO for Advanced Convergence. Figure 10. Red Convergence Menu Advanced Convergence Figure 11 After adjusting the Red Convergence and Blue Convergence, you can fine-tune your TV by adjusting the Red and Blue convergence at 64 individual points. 1. Move the flashing bracket to a position needing adjustment by pressing ADJUST , , or . 2. Press ENTER to select the position (flashing will stop). 3. Move the Red or Blue line by pressing , , or . 4. Press ENTER to deselect the position (flashing will resume), and move the brackets to the next position needing adjustment. 5. Press VIDEO to switch between the Red and Blue lines. A position is properly converged when all three lines combine to appear white. 6. When completed, press MENU or HOME to save your changes, and exit the Advanced Convergence screen. Press INFO for help 7. You may also press INFO to display detailed instructions on using the Advanced Convergence. Then press INFO or MENU to return to the Advanced Convergence menu. Figure 11. Advanced Convergence Menu Although there are more than 64 line intersections, the flashing bracket only stops at 64 adjustment positions. IMPORTANT Reset Factory Defaults Menu Figure 12 This allows you to reset the convergence to the original factory settings. The message “Convergence reset completed” will be displayed when the factory defaults have been restored. WARNING: RESET CONVERGENCE TO FACTORY DEFAULTS. All manual changes to red and blue convergence and advanced convergence will be deleted. Press ENTER to Reset convergence to the defaults. Press HOME or MENU to return to the menu without resetting convergence. Figure 12. Reset Factory Defaults Menu NetCommand® Menu NetCommand Menu Figure 13 Figure 13. NetCommand menu Detailed information for setting up and editing the NetCommand menu is found in Chapter 3. Edit NetCommand allows you to add new devices, change or edit traditional and IEEE 1394 devices, turn devices and unused inputs On or Off, delete a single device or the entire setup configuration. If you choose to delete the entire configuration, or if the NetCommand setup was cancelled, deleted or not completed, you can start at the Initial NetCommand screen. The Review screen shows all devices connected to the TV, including IEEE 1394 devices. Transport Menu Figure 14 Main Picture Figure 14. Transport Menu NetCommand uses the Transport menu to control VCRs, DVDs, IEEE 1394 AV Discs, digital VCRs, and similar devices. If you choose to turn off this menu when viewing the devices, the transport buttons (rewind, play forward, stop, pause and record) on the TV’s remote control will continue to operate these devices. In the Device Selection menu selecting a VCR or DVD Player will automatically display the Transport menu. Re-display this menu by pressing DEVICE MENU. Select Transport menu functions by pressing ADJUST or and then ENTER. For example, to pause playback, press ADJUST or to move to PAUSE, then press ENTER. If a function is not possible, such as record for a DVD Player, the Transport menu button will be grayed out. Remote Control Transport Buttons PAUSEREW/REV FF/FWDPLAYSTOPRECCONNECT STOP Transport buttons (rewind, Transport play forward, stop, pause and Buttons record) on the remote control are located in the bottom section of the remote control. Default Digital Record Device If multiple recording devices are available in NetCommand, this setting allows you to choose the device to use when recording digital programs. A digital recording can be made on either a digital or analog device although the quality will not be as good if recorded on an analog device. For best playback quality, record digital programs on a digital recording device. If multiple devices were not connected and then added in the NetCommand setup, this setting will be unavailable (grayed out). Analog recordings ca...

Baixe o seu

Para fazer o download, introduza 2 dígitos :