Assessments - 2, GPA: 3 ( )

Fabricante : JVC Arquivo Tamanho: 8.25 mb Arquivo Nome : Língua de Ensino:

This will allow the NetCommand system to use the TV outputs to transfer the device’s audio to the A/V Receiver. See Edit NetCommand in the next chapter for details. Q. I have both the TV stereo audio output and TV digital audio output connected to the same input designations on my A/V Receiver. How do I switch between analog audio and digital audio? A. In most setups, analog audio is also output as digital audio, so no switching is required, and there is no need to connect the analog output. In some circumstances, however, you may also need analog audio from the TV. For example, MP3 audio is only output in analog format, so you must connect the TV’s analog AUDIO OUTPUT to the A/V Receiver if you want to hear MP3 audio through the A/V receiver. Refer to your A/V Receiver user’s guide to find out how analog/digital audio switching works. • If your A/V Receiver’s remote control has an Analog/Digital Audio key, you can use the GUIDE key with the following models to control switching: Mitsubishi M-VR900 Integra DTR-9.1 Denon AVR-2700 Kenwood VR-2080 To make the switch, press the Device key on the TV’s remote control, and from the Device Selection menu, press the Audio key. Then, with the A/V Receiver highlighted, press the GUIDE key to make the switch. • If you have some other A/V Receiver model, use the TV’s learn function to learn the analog/digital audio code for the GUIDE key. Follow the instructions above for using the GUIDE key. • If your A/V Receiver has an Analog/Digital selection key on the front panel only, and not on the remote, then your only option is to use that key to perform switching. Q. The front panel of my A/V Receiver is too tall or too convex for the IR emitter signal to reach the remote control sensor of the A/V Receiver. What can I do? A. There are several possible solutions. 1. Mount the IR Emitter on the top, front edge of the A/V Receiver over the remote control sensor. Use tape to secure it in place. 2. Mount the IR Emitter on the underside of the shelf above the A/V Receiver (if the A/V Receiver is in a cabinet). Use double sided tape to secure it in place. 3. Some small stick-on emitters from other manufacturers may be compatible with this TV’s IR Emitter jacks. These may be used instead of the supplied IR Emitters. Q. I occasionally need to see the menu from my A/V Receiver. How can I connect it to the TV for this purpose? A. You can connect the video output of the A/V Receiver to an unused input on the TV. Then use Edit NetCommand to “Add” this as an “Other” device, not an A/V Receiver. On the “Connection” screen, indicate which TV input was used and check mark the video box. Make sure the TV input audio box and both the audio and video boxes for the AVR input are not check marked. You should also name this device so you can easily identify it on the Device Selection Menu. You can also use Input 3 on the front panel. Q. I have a high definition receiver I would like to connect and it also has an S-video output I would like to be able use as well. Is there any way to connect this receiver both ways? A. Yes, this item will appear twice in the Device Selection Menu. Just add this unit once using the Component-1 and once using one of the S-video inputs. Make sure you indicate that this is the same manufacturer for both. We suggest that you connect stereo audio outputs with the S-video to the TV so that you do not need to use two inputs on the A/V Receiver. If this is a NetCommand compatible HDTV receiver and HD or SD outputs can be switched by remote control, see Edit NetCommand in the next chapter for NetCommand control of this feature. 3 NetCommand® Setup and Editing NetCommand® Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Using the Remote Control with NetCommand® . . . . . . . . . . . . . . 37 NetCommand® Setup On-Screen Buttons.. . . . . . . . . . . . . . . . . . 38 3D Graphical Menu System. . . . . . . . . . . . . . . . . . . . . . 39 NetCommand® Initial Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Adding an A/V Receiver.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Adding Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Changing or Deleting Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . 50 IEEE 1394 Devices and NetCommand® Control.. . . . . . . . . . . . . . 51 Adding IEEE 1394 Devices Automatically.. . . . . . . . . . . . . . . . . . . 52 NetCommand® Introduction NetCommand makes your TV the heart of your Home Theater NetCommand® is an intelligent control system that makes your Mitsubishi TV the heart of your home theater. With NetCommand, the TV sends signals to the other devices in the system via the IR emitters, telling the devices to play, record, change inputs, adjust volume, change channels and many more functions. All of this is accomplished with one remote control and without changing control layers. IR Learning and IEEE 1394 Support The IR “Learning” feature...

Baixe o seu

Para fazer o download, introduza 2 dígitos :