Assessments - 4, GPA: 4.5 ( )

Fabricante : JVC Arquivo Tamanho: 2.67 mb Arquivo Nome : Língua de Ensino:

To send audio from TV channels received on ANT 1, ANT 2, or devices connected directly to the TV, you must use one of the connections shown below. The TV makes all audio available in digital and analog formats: • Analog audio coming into the TV is available as output in digital stereo format on the DIGITAL AUDIO OUTPUT jack. • Digital incoming audio is available as analog output on the AVR AUDIO OUTPUT L and R jacks. Usually, only one of the following audio connections is required: To connect an analog A/V receiver • Connect left (white) and right (red) audio cables from AVR AUDIO OUTPUT L and R on the TV back panel to the TV AUDIO INPUT on the A/V receiver. • To connect a digital A/V receiver with Dolby Digital surround sound and PCM audio support: Connect one end of the digital audio cable to DIGITAL AUDIO OUTPUT on the back of the TV. Connect the other end to the COAXIAL DIGITAL INPUT on the back of the A/V receiver. HDMI 3D GLASSES EMITTER ANT 2 R L R L (480i / 480p / 720p / 1080i) DVI/PC INPUT VIDEO Y Pb Pr AUDIO Y/ VIDEO Pb Pr VIDEO: 480i/480p/720p/1080i/1080p AUDIO: PCM STEREO PC: VGA, W-VGA, SVGA, W-SVGA, XGA, W-ZGA, SXGA, 720p/ 1080p 1 2 3 HDMI IR-NetCommand Output / External Controller Input R INPUT 1 INPUT 2 INPUT 3 S-VIDEO INPUT 3 R AUDIO L AUDIO ANT 2 / AUX ANT 1 / MAIN AVR AUDIO OUTPUT DIGITAL AUDIO OUTPUT L R DIGITAL AUDIO OUTPUT AVR AUDIO OUTPUT L R ................ .......... ................ .......... .......................................... .................................... .......................................... ........................................ ...................................... ........................................ .......................... .............................................. .... .... .... .... .... .... .... .... .... ........ Figure 11. Connecting the TV to an A/V receiver Note: • On rare occasions, an HDMI signal may be copy-restricted and cannot be output from the TV as a digital signal. To hear these copyprotected signals through the A/V receiver, use the connection for an analog A/V receiver. • Check the A/V receiver’s Owner’s Guide for information concerning use of the digital input and switching between digital sound and analog stereo sound from the TV. A/V Receiver with HDMI Output Required: One HDMI-to-HDMI cable This option allows you to view content from devices connected to an A/V receiver. The A/V receiver can send audio and video to the TV over a single HDMI cable. You can use an HDMI connection as described here in addition to an audio connection from the TV’s audio output. All models: You may be able to use the TV’s remote control (with slide switch set to TV) to operate connected CEC-enabled HDMI devices without further setup. Experiment with your equipment to determine which functions are available to the TV’s remote control. See “NetCommand for HDMI Devices,” page 28. 736 and 835 series models only: This setup allows you to use NetCommand-controlled audio and video switching over the HDMI cable. See “A/V Receiver Control: Automatic Video and Audio Switching via HDMI” on page 60. HDMI 3D GLASSES EMITTER AVR AUDIO OUTPUT DIGITAL AUDIO OUTPUT L R R L R L (480i / 480p / 720p / 1080i) DVI/PC INPUT VIDEO Y Pb Pr AUDIO Y/ VIDEO Pb Pr VIDEO: 480i/480p/720p/1080i/1080p AUDIO: PCM STEREO PC: VGA, W-VGA, SVGA, W-SVGA, XGA, W-XGA, SXGA, 720p/ 1080p 1 2 3 HDMI IR-NetCommand Output / External Controller Input R INPUT 1 INPUT 2 INPUT 3 S-VIDEO INPUT 3 R AUDIO L AUDIO ANT 2 / AUX ANT 1 / MAIN ................ .............................. .................... .................... .................. ...... .......................... .... .... .... .... .... .... .... .... .... .... .... .................................... ...................... Figure 12. A/V receiver connected to the TV with an HDMI cable may offer special control capabilities. 25 3. TV Connections Camcorder Inputs on the front of the TV (INPUT 4) offer the most convenient way to connect a camcorder, although you can use jacks located on the back panel instead. Three different connection options are described on this page. Use jacks on the TV front panel to connect a camcorder A: Y Pb Pr Component Video Connection Required: Component video and analog stereo audio cables supplied with the camcorder. 1. Connect component video cables from VIDEO OUT on the camcorder to the TV’s Y Pb Pr component jacks on the front panel. 2. Connect left (white) and right (red) audio cables from AUDIO OUT on the camcorder to AUDIO L and R on the TV. L-AUDIO-RVIDEO/YPbPrUSB HDMI 4DVI AUDIOI N P U T 4L-AUDIO-R HDMI 4DVI AUDIO VIDEO/Y Pb Pr L-AUDIO-R VIDEO/Y Pb Pr .......................................................................... HDMI 4L-AUDIO-R VIDEO/Y .................................................................................................................................................................................... ........................................T Figure 13. INPUT 4 on...

Baixe o seu

Para fazer o download, introduza 2 dígitos :