Log:
Assessments - 3, GPA: 4.7 ( )

Instruções de Operação Hunter Fan, Modelo 44050

Fabricante : Hunter Fan
Arquivo Tamanho: 455.71 kb
Arquivo Nome :
Língua de Ensino: en
Ir para baixar



Facilidade de uso


¦ Remove existing thermostat cover and thermostat. 1. Some thermostats will have screws or other locking devices that must first be removed. Once wall mounting plate is exposed, look for wires. If wires are not visible, they may be connected to the back of the wallplate. screws, tabs, etc. Some models have doors that open to expose wires and mounting screws. (See Figure 1). TYPICAL THERMOSTATS FIGURE 1 Wall Mounting Plate Thermostat Cover Wall Mounting Plate Thermostat Cover 10-11Installation Label Wires ¦ Each wire coming from the wall to the existing that thermostat. Each of Table A on page 9. The number of wires in your system can be as few eight, or any number in between. correctly, you do not have to be concerned about how many wires there are. There is often no terminal marking on the existing heat only systems. Do not worry, just connect either of the wires to the RH terminal, then connect the other to the W terminal to complete the circuit. ¦ IMPORTANT! BEFORE DISCONNECTING ANY WIRES, APPLY THE SELF-ADHESIVE LABELS PROVIDED TO THE WIRE AS SHOWN IN TABLE A ON PAGE 11. (For example, attach the label marked W to the wire which goes to the W or H terminal on your existing IGNORE THE COLOR OF THE WIRES since these do not always comply with the standard. ¦ After labeling wires, disconnect them from the existing thermostat terminals. ¦ Remove existing wallplate. To make sure wires do not fall back into wall opening, you may want to tape them to the wall. ¦ If hole in wall is larger than necessary for wires, seal this hole so that no hot or cold air can enter the back of the thermostat from the wall. This air could cause a false thermostat reading. W G Y RH RC RH G Y W RC RH RH RC RC G G Y Y W W RH, R, VR or 4 24 Volt G or F Fan RC, VC 24 Volt Cool Y, C or M (See Note) Air Conditioning W or H Heating RED BLUE GREEN YELLOW WHITE RH, R, VR or 4 24 Volt G or F Fan RC, VC 24 Volt Cool Y, C or M (See Note) Air Conditioning W or H Heating RED BLUE GREEN YELLOW WHITE 12-13Installation Wire Labeling (Continued) NOTE: If your thermostat has the jumper wire between and RC terminals. Otherwise, RH and RC wires (5-wire system), RC terminals. NOTE: Do not connect a “Common” wire this thermostat. Tape up the wire and do not use. Mount Snap open the your thermostat the release tab on the the thermostat. Position wallplate on through large opening. Then level appearance. Mark holes if existing holes Hunter Thermostat holes. Drill holes with 3/16" bit and gently Reposition wallplate to wall, pulling through large opening. Insert mounting screws provided into wall anchor and tighten. 2.) FIGURE 2 14-15Installation Selector Switches The heating system selector switches are located on the Printed Circuit Board. ¦ Heating system selector The heating system selector is Board on the inside of the thermostat. The switch is at “HG” furnace or an oil burner. If you have an electric furnace, test to see whether the heat and expected. Leave the switch in the “HG” thermostat...

Este manual também é adequado para os modelos :
Os termostatos - 42999 44050S (455.71 kb)
Os termostatos - 42999 44050S (455.71 kb)
Os termostatos - 42999 44050S (455.71 kb)
Os termostatos - 44050 (455.71 kb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias