Assessments - , GPA: ( )

Instruções de Operação Hunter Fan, Modelo 43154

Fabricante : Hunter Fan
Arquivo Tamanho: 292.92 kb
Arquivo Nome : 43154.pdf

Língua de Ensino:

O documento está colocado, por favor, espere

Baixe o seu Fechar

O documento está colocado, por favor, espere

Baixe o seu Fechar

¦ Press again to change to your desired Set 3COOL TEMP Temperature. Hold the key for 2 seconds to or fast-advance the Set Temperature. ¦ Press to return to normal mode, or wait 5 seconds for it to return automatically. /return ¦ The current program number will flash to SA signify the Temporary Override. ¦ At the next program change time, the Tem-PM porary Override is cancelled, and the next program temperature becomes the setpoint COOL TEMP 3 temperature. To end the Temporary Manual Override: hold ¦ Press, then press again. This will return the set temperature to the current program set temperature. /return Permanent Override To hold your Manual Override for vacation or just an extended period of time: /return ¦ Press to make the current program temperature the HOLD temperature. HOLD will be displayed on the LCD, and the Program number will disappear. ¦ Follow the Temporary Manual Override instructions above to change the Permanent Manual Override temperature. ¦ You can confirm the held set temperature by pressing for less than 1 second. hold TH PM HOLD TEMP To end the Permanent Manual Override: hold ¦ Press again. The thermostat will return to the current program, and the HOLD display will be canceled. /return Filter Change Indicator Your thermostat measures the number of hours your heating and cooling system has been in use. To maximize your system’s performance and energy efficiency, change or clean your filter regularly. M T W TH F SA SU SET TEMP AM 2PM FILTER filter COOL TEMP seconds. The display will blink, and the timer will be reset to zero. Note: Pressing the Filter Key at any time for less than 3 seconds will cause the Filter indicator to appear on the LCD. This is only to confirm key operation, and the timer is not affected unless the key is held for greater than 3 seconds. SPAN Setting Mode Your thermostat is set at the factory to cycle at 1°F (0.5°C) above and below the set temperature. (Span = 2) This setting has been designed to provide a comfortable room temperature under most all conditions. However, if you find your system cycling too fast or too slow, then the Span can be adjusted to modify the cycle time. ¦ Press and hold BOTH for three seconds. The display will flash, and SPAN will be displayed on the LCD. ¦ Press to raise the Span to 3. This setting INCREASES the cycle time by allowing your system to run LONGER. ¦ Press to lower the Span to 1. This setting DECREASES the cycle time by causing your system to run SHORTER. The Span settings remain the same for both HEAT and COOL. The Span can be changed at any time, and is independent of program times or temperatures. When batteries are installed in the thermostat, or the Reset key is pressed, the Span is reset back to setting 2. Backlighting (INDIGLO® Night-Light) Your thermostat has an electroluminescent lamp that backlights the display for easy viewing in the dark. When any key is pressed or the System Switch is changed, the display is illuminated. The display will remain illuminated for 5 seconds after the last key is pressed. This allows the light to stay on if you need to operate several keys. Note: If the thermostat is in Low Battery warning condition, the backlight will not operate. Replace with 2 new alkaline batteries to restore the Backlight function. Low Battery Warning Your thermostat has a two-stage low battery warning system. When the batteries are first detected to be weak, the first stage low battery warning is indicated by battery symbol flashing on the LCD display. At your earliest convenience, you need to replace the batteries with 2 new AA alkaline batteries. When the batteries become too weak for normal operation, the thermostat enters the second stage low battery warning which shuts down the thermostat. In this condition, “BATT” flashes alone on the display, and the thermostat will turn your system Off. Your system will remain shut-off until the batteries are replaced. T PM 3 HEAT TEMP Note: The thermostat will still keep the current time and your programs in memory until new batteries are installed. After confirming that new batteries have been inserted, the thermostat will return to normal operation. Auto Recovery Climate Technology’s Auto Recovery feature meets the ENERGY STAR® guidelines for energy efficiency by allowing the heating or cooling system to recover gradually from an energy- saving setpoint temperature to a comfort setpoint temperature. Auto Recovery calculates how early to turn your system back On, so that the room temperature is already comfortable by the start of the comfort temperature program period. Auto Recovery works in both Heat and Cool modes. ¦ When the thermostat is in Auto Recovery mode, the display will alternate “RECO” with time, and the program indicator will flash. ¦ Auto Recovery can be disabled by sliding the Recovery switch on the circuit board to disable. ¦ Auto Recovery will not operate if Permanent hold or Temporary hold is in operation. ¦ Auto Recovery can be canceled manually ...