Assessments - 4, GPA: 5
(
)
)
|
Facilidade de uso
STEP 6: program program hold /return SA PM TEMP 2 MT WTHF AM 1 HEAT MT WTHF AM 1 HEAT MT WTHF AM 1 HEAT ¦ Press again to move to the next program number. ¦ Repeat Steps 3 through 5 to change the remaining Weekday, Saturday, and Sunday programs. (There are a total of 12 programs.) ¦ After cycling through all 12 programs, press again to return the display to normal. ¦ Press at any time to exit the Program Mode. ® Reviewing Programs To review your program settings, press program repeatedly to cycle through the programs. You can also make changes at any time. System Selector Switch The System Selector switch on the front of the thermostat determines the operating mode of the thermostat. You may select COOL, OFF, HEAT. NOTE: Anytime you install or remove the thermostat from the wallplate, slide the System Selector to the OFF position to prevent the possibility of a rapid system On-Off. Fan Switch The Fan switch should normally be located in the AUTO position. The Fan will be turned on along with normal operation of your system. In a normal gas or oil furnace, the Fan will be turned on by your furnace after its warm-up delay. For electric heat, air conditioning, and heat pump operation, the Fan will turn on with the system. system heat off cool fan auto on To run the Fan on continuously, slide the Fan switch to the ON position. Temporary Manual Override To temporarily change the current set temperature without affecting your program: hold ¦ Press and hold for about 1 second to enter Manual Override mode. When or display flashes, you can release the key. ¦ Press again to change to your desired Set Temperature. Hold the key for 2 seconds to or fast-advance the Set Temperature. ¦ Press to return to normal mode, or wait 5 seconds for it to return automatically. /return ¦ The current program number will flash to signify the Temporary Override. ¦ At the next program change time, the Temporary Override is cancelled, and the next program temperature becomes the setpoint temperature. To end the Temporary Manual Override: SET TEMP 3 COOL TEMP SA PM COOL TEMP 3 hold ¦ Press, then press again. This will return the set temperature to the current program set temperature. /return Permanent Override To hold your Manual Override for vacation or just an extended period of time: /return ¦ Press to make the current program temperature the HOLD temperature. HOLD will be displayed on the LCD, and the Program number will disappear. ¦ Follow the Temporary Manual Override instructions above to change the Permanent Manual Override temperature. ¦ You can confirm the held set temperature by pressing for less than 1 second. hold TH PM HOLD TEMP To end the Permanent Manual Override: hold ¦ Press again. The thermostat will return to the current program, and the HOLD display will be canceled. /return Filter Monitor Your thermostat measures the number of hours your heating and cooling system has been in use. To maximize your system’s performance and energy efficiency, change or clean your filter regularly. filter mode, or you can press the HOLD/RETURN key to exit immediately. ¦ After changing or cleaning the system’s filter, press and hold the Filter Key for 3 seconds. The display will blink, and the timer will be reset to zero. M T W TH F SA SU SET TEMP AM PM FILTER 2 COOL TEMP HR MIN SPAN Setting Mode Your thermostat is set at the factory to cycle at 0.5°C (1°F) above and below the set temperature. (Span = 2) This setting has been designed to provide a comfortable room temperature under most all conditions. However, if you find your system cycling too fast or too slow, then the Span can be adjusted to modify the cycle time. ¦ Press and hold BOTH for three seconds. The display will flash, and SPAN will be displayed on the LCD. ¦ Press to raise the Span to 3. This setting INCREASES the cycle time by allowing your system to run LONGER. ¦ Press to lower the Span to 1. This setting DECREASES the cycle time by causing your system to run SHORTER. The Span settings remain the same for both HEAT and COOL. The Span can be changed at any time, and is independent of program times or temperatures. When batteries are installed in the thermostat, or the Reset key is pressed, the Span is reset back to setting 2. Low Battery Warning Your thermostat has a two-stage low battery warning system. When the batteries are first detected to be weak, the first stage low battery warning is indicated by battery symbol flashing on the LCD display. At your earliest convenience, you need to replace the batteries with 2 new AA alkaline batteries. When the batteries become too weak for normal operation, the thermostat enters the second stage low battery warning which shuts down the thermostat. In this condition, “BATT” flashes alone on the display, and the thermostat will turn your system Off. Your system will remain shut-off until the batteries are replaced. T PM 3 HEAT TEMP Note: The thermostat will still keep the current time and your programs in memory until new batteries ...
Este manual também é adequado para os modelos :Os termostatos - 47200A (308.35 kb)
Os termostatos - 47200A (308.35 kb)