Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
1 INSTALLATIONCONSIDERATIONS ................... 1 INSTALLATION .................................... 1 Step1—ThermostatLocation ........................ 1 Step2—InstallThermostat ........................... 2 Step3—SetThermostatConfiguration ................. 2 Step4—UnderstandThermostatOperation .............. 2 Step5—CheckThermostatOperation .................. 3 WIRINGDIAGRAMS ................................ 4 SAFETY CONSIDERATIONS Read and follow manufacturer instructions carefully. Follow all local electrical codes during installation. All wiring must conform to local and national electrical codes. Improper wiring or installation may damage thermostat. Recognize safety information. This is the safety- --alert symbol . When you see this symbol on the equipment and in the instruction manual, be alert to the potential for personal injury. Understand the signal words DANGER, WARNING,and CAUTION. These words are used with the safety- --alert symbol. DANGER identifies the most serious hazards which will result in severe personal injury or death. WARNING signifies a hazard which could result in personal injury or death. CAUTION is used to identify unsafe practices which may result in minor personal injury or product and property damage. NOTE is used to highlight suggestions which will result in enhanced installation, reliability, or operation. INTRODUCTION There are two Legacy Line--RNC Series programmable thermostat models, one for AC applications and one for HP applications. Both are dual powered, operating from either 24VAC or two alkaline AA batteries. Configuration and program schedules are stored in non- --volatile memory, preserving this information during power loss and battery removal. Features include simplified 5/2 programming, large backlit display, and modern styling. The AC model provides one stage of heating and one stage of cooling. The HP model provides two stages of heating and one stage of cooling. INSTALLATION CONSIDERATIONS AC Operation For 24VAC operation, both the R and C wires must be connected to the 24VAC power source. Batteries are not needed. Battery Operation When batteries are used, the common (C) connection is not needed, saving a wire, and eliminating 24VAC operation. The thermostat continues to operate in the event of a power failure. Battery life is expected to be one year. A “low battery” reminder tells the homeowner when it is time to replace the batteries. When connected without the common wire, the thermostat will not operate without batteries. Continuous back- --lighting is not available. Both Battery and AC Operation If both batteries and 24VAC operation are used (batteries installed and the common wire connected), and indefinite clock operation are provided, the battery will be used only during AC power loss, extending battery life to nearly its shelf life. A jumper has to be properly set for backlight operation. J2 should be set in the “AC” position when the thermostat is operated from 24VAC. J2 should be set in the “BAT” position when the thermostat is operated from batteries. The thermostat will continue to operate if J2 is not in the correct position or not connected. However, the backlight will not operate. INSTALLATION Step 1 — Thermostat Location Thermostat should be mounted: S Approximately 5 ft (1.5m) from floor. S Close to or in a frequently used room, preferably on an inside partitioning wall. S On a section of wall without pipes or duct work. T1PAC/ T1PHPT1PAC/ T1PHP Thermostat should NOT be mounted: S Close to a window, on an outside wall, or next to a door leading to the outside. S Exposed to direct light and heat from the sun, a lamp, fireplace, or other heat- --radiating object which may cause a false reading. S Close to or in direct airflow from supply registers and return- --air grilles. S In areas with poor air circulation, such as behind a door or in an alcove. Step 2 — Install Thermostat ! WARNING ELECTRICAL OPERATION HAZARD Failure to follow this warning could result in personal injury or death. Before installing thermostat, turn off all power to unit. There may be more than 1 disconnect. Lock out and tag switch with a suitable warning label. 1. Turn OFF all power to unit. 2. If an existing thermostat is being replaced: a. Remove existing thermostat from wall. b. Disconnect wires from existing thermostat, one at a time. Be careful not to allow wires to fall back into wall. c. As each wire is disconnected, record wire color and terminal marking. d. Discard or recycle old thermostat. CAUTION! ENVIRONMENTAL HAZARD Failure to follow this caution may result in environmental damage. Mercury is a hazardous waste. Federal regulations require that Mercury be disposed of properly. 3. Separate front and back plastic assembly of thermostat. 4. Route thermostat wires through hole in mounting base. Level mounting base against wall (for aesthetic value only, thermostat need not be level for proper operation) and mark wall through 2 mounting holes. 5. Drill two 3...
Este manual também é adequado para os modelos :Os termostatos - LEGACY LINE--RNC T1--PHP (173.21 kb)