You may find their name on the furnace or in your Homeowner's Packet. If the installer's name is not known, call your builder or home retailer if yours is a new residence. SECOND: Contact the nearest distributor. (See telephone yellow pages.) THIRD: Contact: Carrier Corporation Consumer Relations P.O. Box 4808 Syracuse, New York 13221 Phone: 1-800-428-4326 Model No.__Unit Serial No._ Date of Installation__Installed by_ Name of Owner__Address of Installation_ THERMOSTAT LIMITED WARRANTY F

Follow all local electrical codes during installation. All wiring must conform to local and national electrical codes. Improper wiring or installation may damage thermostat. Recognize safety information. This is the safety-alert symbol . When you see this symbol on the equipment and in the instruction manual, be alert to the potential for personal injury. Understand the signal words DANGER, WARNING, and CAUTION. These words are used with the safety-alert symbol. DANGER identifies the most seriou

Also remove the two plastic hole plugs (see illustration). 4. Install thermostat from back side of front panel and fasten in place, from front, with two screws and washers provided (see illustrations). 5. Attach temperature control knob by gently pushing it on to the thermostat shaft. Flats on shaft and knob must line up for proper installation (do not force control knob onto shaft). 6. Remove black wire from thermal fuse and attach it to thermostat terminal marked “4”. 7. Remove white wire

7 (4/08) Page 1 of 2 ELECTRICAL SPECIFICATIONS: Model No. Volts Watts Amps Hertz Phase Service CSH-122-10 120 1100 9.2 60 1 5-15 15 AMP CSH-122-10 240 1150 4.8 60 1 6-15 15 AMP 0595-002 HOW TO OPERATE UNIT: 1. Plug cord into proper wall outlet. 2. Push thermostat switch “ON” and turn thermostat to no. 10. 3. Preheat for 30 minutes; then add cutting board and/or pans to the heated base. 4. Push lamp switch(es) to “ON” for additional heat. NOTE: Proper food holding temperature is 140°F

GENERAL Totaline® thermostats are wall-mounted, low-voltage thermostats which maintain room temperature by controlling theoperation of an HVAC (heating, ventilation and air conditioning) system using separate heating and cooling set points andauto-changeover capability. Batteries are not required. During power interruption theinternal memory stores set points indefinitely. OPERATION Thermostat Display — The thermostat display is located in the top center of the thermostat. See Fig. 1. The follow

GENERAL This manual will assist you in using your Carrier Comfort System thermostat. There are 2 basic types of thermostats that you may encounter. They are called the monitor thermostat and the zone controller. The monitor thermostat can be identified by the system switches (FAN, HEAT, COOL) which are located along the bottom edge of the front cover. The monitor thermostat can be equipped with or without a timeclock. The timeclock display is located in the upper right corner of the monitor ther

Your new T8132C Thermostat automatically controls the temperature in your home, keeping you comfortable while saving energy when programmed according to the instructions in this manual. Direct questions concerning the operation of this thermostat to Honeywell Customer Assistance at 1-800-468-1502, Monday-Friday 7:00 a.m.-5:30 p.m., Central time. 2 69-0786—2 Table of Contents Page Programming Thermostat ..............................................................................................

HEAT AUTOFAN AUX. HEAT * Air Conditioner Model * Heat Pump Model (HH07AT212) (HH07AT214) NON-PROGRAMMABLE THERMOSTAT ® * Standard Model (AC, HP, 2S) PROGRAMMABLE THERMOSTAT AND THERMIDISTATTM CONTROL ® * Standard Model (AC, HP, 2S) * Dual Fuel Model (DF) * ThermidistatTM Control Model (RH) The Bryant electronic thermostat product line consists of programmable and non-programmable air conditioner, heat pump, and 2-speed models; a programmable dual fuel model, and a programmable ThermidistatTM Con

To ensure the schedules are properly followed, make sure that AM or PM is correct for the time chosen. When the correct time is shown, press the End button to exit the Set Time mode. V. RESET FILTER The Reset Filter function is used to clear the “Clean Filter” icon on the display screen. The Reset Filter function is initiated by pressing the Hold and Occupied buttons simultaneously. The “Clean Filter” icon reminds the user when it is time to change or clean the filter of the unit. VI. PROGRAMMIN

GENERAL Bryant’s 7-day, commercial, programmable thermostats are wall-mounted, low-voltage thermostats which maintain room temperature by controlling the operation of an HVAC (heating, ventilation, and air conditioning) system. Separate heating and cooling set points and auto-changeover capability allow occupied and unoccupied programming schedules for energy savings. All thermostats allow up to 4 time and temperature settings to be programmed per 24-hr period. Each thermostat stores programs fo