In Hold mode, the thermostat will not change its settings by program. 3- Prog Press the Prog (programming) key to set the current time and day (hours, minutes, day of week), and to program the temperature time schedules for the MORN, DAY, EVE, and NITE periods. AUTO DAY COOL : P 4- Mode Press the Mode key to set the thermostat mode to Off, Heat, Cool, or Auto. In Off mode, the heating and cooling systems are both off and do not respond to changes in temperature settings. .. In Heat mode, the hea

Both the current time and all programs will automatically change to the selected format. The time format may time, press option at any time while the Hour, Minute, also be changed in the Option Menu. or Day is flashing to toggle between the 12 hour and 24 hour 41652_model44760_web.pmd 20 21 PROGRAMMING Programming Introduction Studies conducted by the Department of Energy estimate that You can program weekdays as a group, weekends as a group, all setting your thermostat back 10°F (6°C) for two 8

Set the switch to HG for a gas furnace or oil burner. Set the switch to HE for electric furnaces. (The switch has no effect when the system is set to cooling mode.) 5. Insert two fresh AA alkaline batteries. 6. Align the thermostat with the the wall plate, and snap the two halves together. 7. Restore power at the electrical panel or furnace. Thermometer System Switch Set Temperature Slider Fan Switch Battery Indicator Operation 1. Set the Set Temperature slider to the desired temperature. 2. The

¦ Press again to change to your desired Set 3COOL TEMP Temperature. Hold the key for 2 seconds to or fast-advance the Set Temperature. ¦ Press to return to normal mode, or wait 5 seconds for it to return automatically. /return ¦ The current program number will flash to SA signify the Temporary Override. ¦ At the next program change time, the Tem-PM porary Override is cancelled, and the next program temperature becomes the setpoint COOL TEMP 3 temperature. To end the Temporary Manual Override: ho

1 MAINTENANCE............................................................................................... 1 OPERATION ..................................................................................................... 2 DISPLAY ............................................................................................................ 4 FILTER REMINDER ....................................................................................... 6 ANTICIPATION .....................................

4. Using the provided stickers, label each wire according to the Wire Labels chart. (If the terminals are not labeled, contact a qualified HVAC technician.) Note: Wire colors do not always comply with standards, so wire color should be ignored. Refer to the existing terminal designation for proper identification. *If wires marked Y & C are both present, C may be a Common wire and should not be used. If you have a wire marked C, do not connect it to any terminal. This wire is used only for non-ba

• If the wiring to the thermostat has been correctly connected, and if the thermostat has been correctly mounted to the wallplate, then the LCD Display should show the indoor room temperature. THERMOSTAT CONTROLS • Open the thermostat’s front cover. See Figure 6. Figure 6 Switches and Buttons K J A I B sys aux em H program system G day/time em heat F filter fan heat auto off refresh cool E hold/rtrn C reset on D Switches and Buttons A LCD Readout - displays indoor temperature, set temperature, a

¦ Remove existing thermostat cover and thermostat. 1. Some thermostats will have screws or other locking devices that must first be removed. Once wall mounting plate is exposed, look for wires. If wires are not visible, they may be connected to the back of the wallplate. screws, tabs, etc. Some models have doors that open to expose wires and mounting screws. (See Figure 1). TYPICAL THERMOSTATS FIGURE 1 Wall Mounting Plate Thermostat Cover Wall Mounting Plate Thermostat Cover 10-11Installation La

This thermostat will not control line voltage systems. You will need the following tools to complete your installation: • Phillips Screwdriver (#2) • Two 1.5V (AA) size alkaline batteries Take note of these warnings and cautions before proceeding: • Read all installation instructions before beginning installation! If you still need assistance after reading this manual, call our Technical Support at 1-888-830-1326. • Do not disconnect the wires from your old thermostat until all wires have been p

44040-01 • 03/24/201018 ©2010 Hunter Fan Company 19 5 Temporary Schedule Change Scheduling Home Menu Schedule setting temporary temperature hold Cool to 73o1 Done Home Menu Schedule setting temporary temperature hold Cool to 73o2 Done Home MenuSchedule temporary hold[resume] to run schedule Cool to 73o74o Auto3 Energy Savings: GoodBest! At homeResume ©2010 Hunter Fan Company 19 5 Temporary Schedule Change Scheduling Home Menu Schedule setting temporary temperature hold Cool to 73o1 Done Home Men