Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
Before reading further, please familiarize yourself with the parts that are labeled in the drawing below. Handrail Fan Personal Television/Console Book Holder Key/Clip Reset/Off Circuit Breaker Walking Belt Foot Rail Power Cord Cushioned Walking Platform Rear Roller Adjustment Bolts Accessory Tray Pulse Sensor 6 ASSEMBLY Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner. Assembly requires the included hex key identifying the assembly hardware, see the drawings below. and your own Phillips screwdriver . For help The number in parentheses below each drawing is the key number of the part, from the PART LIST on pages 26 and 27. The number following the parentheses is the quantity needed for assembly. Note: Some small parts may have been preassembled. If a part is not in the parts bag, check to see if it has been preassembled. To avoid damaging plastic parts, do not use power tools for assembly. 2” Silver Screw (48)–13/4” Tek Screw (58)–43Spacer Screw (60)–2141/2” Bolt (78)–41Washer (96)–8nsion Washer(90)–10Nut Bolt (72)–43/4” Screw (4)–4Console Bolt (64)–6 1. Make sure that the power cord is unplugged. With the help of a second person, raise the front of the treadmill and insert the crossbar on the Base (83) into the cutout in the cardboard stand. Have the second person hold the treadmill to prevent it from moving forward or backward until assembly step 2 is completed. WARNING: Serious injury may occur if the treadmill moves forward or backward and falls off the cardboard stand. A second person must hold the treadmill until assembly step 2 is completed to prevent the treadmill from moving, tipping, or falling. 83 Cardboard Stand 1 7 83 76 75 77 74 73 49 97 90 72 95 “Right” “Left” 96 3 74 73 74 73 49 97 90 72 2 2. Identify the Left Upright (73) and the Right Upright (74). Hold the Right Upright near the Right Base Cover (77) as shown. Feed the Upright Wire Harness (75) up into the rectangular hole in the bottom of the Right Upright and out of the top of the Right Upright. Gently pull up on the Upright Wire Harness (75) as you set the Right Upright (74) on the Base (83) inside the Right Base Cover (77). Be careful not to pinch the Upright Wire Harness. Attach the Right Upright (74) to the Base (83) with two Upright Bolts (72) and two Star Washers (90). Note: It may be necessary to tip the tops of the Uprights forward slightly as you thread the Upright Bolts (72) into the Uprights. Hold the Left Upright (73) near the Left Base Cover (76), and insert the TV Cable (49) and the AV Cable (97) up into the rectangular hole in the bottom of the Left Upright and out of the top of the Left Upright. Attach the Left Upright to the Base (83) with two Upright Bolts and two Star Washers (not shown). With the help of a second person, lower the treadmill off the cardboard stand. 3. Identify the Right Upright Sleeve (96) and the Left Upright Sleeve (95). Slide the Right Upright Sleeve onto the Right Upright (74) and the Left Upright Sleeve onto the Left Upright (73). 3 95 73 “Left” “Right” 74 8 4. With the help of a second person, hold the console assembly near the Uprights (73, 74). Connect the Upright Wire Harness (75) to the Console Wire Harness (71). Make sure to connect the connectors properly (see the inset drawing). The connectors should slide together easily and snap into place. If they do not, turn one connector and try again. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. 5. Connect the TV Cable (49) and the AV Cable (97) to the cables extending from the console assembly. Then, insert the connectors down into the Uprights (73, 74). Next, insert the brackets on the Handrails (99) into the Right Upright (74) and the Left Upright (73). Make sure that no wires are pinched. 6. Finger tighten three Handrail Bolts (64) with three Star Washers (90) into the Right Upright (74). Next, finger tighten three Handrail Bolts with three Star Washers (not shown) into the Left Upright (73). Then, firmly tighten the six Handrail Bolts. 71 Console Assembly 4 75 74 49 73 97 5 74 99 73 74 64 64 90 90 75 6 73 99 9 7. Slide the Right Upright Sleeve (96) up against the console assembly. Attach the Right Upright Sleeve with two 3/4" Screws (4). Attach the Left Upright Sleeve (not shown) to the Left Upright (73) as described above. 73 4 96 4 7 8. Note the location of the 75 ohm antenna terminal and the audio/video input jack on the treadmill. For the television to operat...