Assessments - 2, GPA: 5 ( )

Fabricante : Life Fitness Arquivo Tamanho: 1.08 mb Arquivo Nome : 4582e757-90bb-45d6-9b65-f7f627248fb5.pdf Língua de Ensino:

30. Lubricate the 5/16” x 2 1/4” Bolt (33). Attach the Leg Lever (29) to the Seat Frame (36) with the 5/16” x 2 1/4” Bolt and a 5/16” Nylon Locknut (3). 31. Attach the Short Cable (35) to one of the three holes in the Leg Lever (29) with a 5/16” x 3/4” Bolt (89), a 5/16” Washer (8), and a 5/16” Nylon Locknut (3). Note: The three holes are for cable adjustment. Insert the Short Cable between the welded rod and the Leg Lever. Press a 1” Round Inner Cap (49) into each end of the Curl Bar (86). Slide the 1/2” x 3/8” Bushing (91), the Curl Bar, and the Short Cable (35) onto the 5/16” x 1 1/4” Carriage Bolt (90). Hand tighten a 5/16” Nylon Locknut (3) onto the Carriage Bolt. 32. Rest the Seat Frame (36) on the indicated pin in the Front Upright (42). Attach the Seat Frame to the Front Upright with a 5/16” x 2 3/4” Carriage Bolt (14) and the Seat Knob (40). 29 10 18 24 2 36 38 13 37 32 30 33 Lubricate 36 3 29 31 29 3 8 89 8649 35 Welded Rod 3 49 90 91 32 40 36 14 42 Pin 14 SEAT ASSEMBLY 33. Press 3/4” Round Inner Caps (34) into the ends of both 12 1/2” Pad Tubes (28). Insert one 12 1/2” Pad Tube (28) into the Seat Frame (36). Slide a 5 1/2” Pad (30) onto each end of the Pad Tube. Insert the other 12 1/2” Pad Tube (28) into the Leg Lever (29). Slide a 5 1/2” Pad (30) onto each end of the Pad Tube. See the left inset drawing. Insert the head of the 5/16” x 1 1/4” Carriage Bolt (90) into the keyhole in the Leg Lever (29). Be sure that the shoulder of the Carriage Bolt is firmly seated in the square part of the keyhole. See the right inset drawing. Orient the Short Cable (35) and the Curl Bar (86) as shown. Tighten the indicated 5/16” Nylon Locknut (3). Do not overtighten the Nylon Locknut. This is the storage position for the Curl Bar. 34. Attach the Curl Pad (82) to the Curl Frame (84) with four 1/4” x 1/2” Screws (18). Insert a 1 1/2” Square Inner Cap (32) into each end of the Curl Frame (84). Note: These Square Inner Caps may come pre-assembled. 35. Attach the Curl Frame (84) to the Seat Frame (36) by inserting the pin on the Curl Frame into the upper hole in the Seat Frame. Secure the Curl Frame with the Curl Knob (85). 35 85 84 34 33 36 18 18 30 34 34 28 29 82 30 32 36 32 84 18 3 86 35 29 90 Keyhole 15 VKR ASSEMBLY 36. Press 1 1/2” Square Inner Caps (32) into the ends of the Left VKR Arm (79) and the Right VKR Arm (80). Press 1” Round Inner Caps (49) into the ends of the handles on the Left VKR Arm and the Right VKR Arm. Attach the Left VKR Arm (79) and the Right VKR Arm (80) to the Rear Upright (56) with two 5/16” x 3” Bolts (81) and two 5/16” Nylon Locknuts (3). 37. Attach a VKR Armrest (78) to the Right VKR Arm (80) with two 1/4” x 2” Screws (24) and two 1/4” Flat Washers (10). Attach a VKR Armrest (78) to the Left VKR Arm (79) in the same manner. Attach the VKR Backrest (77) to the Rear Upright (56) with two 1/4” x 2 1/2” Screws (43) and two 1/4” Flat Washers (10). 36 81 3 32 32 80 79 10 43 77 78 78 24 80 79 37 49 49 10 56 56 16 38. Remove the decals from the decal sheet (not shown) and apply them to the home gym system in the locations shown in the illustration below. 38 HIGH PULLEY (OTHER SIDE) BUTTERFLY BENCH PRESS PREACHER CURL LOW PULLEY LIFESTYLER SYSTEM 200 VERTICAL KNEE RAISE LEG EXTENSION 39. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in ADJUSTMENT, beginning on page 18 of this manual. Before using the home gym system, pull each cable a few times to be sure that the cables move smoothly over the pulleys. If one of the cables does not move smoothly, find and correct the problem. IMPORTANT: If the cables are not properly installed, they may be damaged when heavy weight is used. See the CABLE DIAGRAM on page 22 of this manual for proper cable routing. I...

Baixe o seu

Para fazer o download, introduza 2 dígitos :