Assessments - 4, GPA: 4.5
(
)
)
|
Fotos e especificações Spirit XT375 |
Facilidade de uso
Now the deck is lubricated and you should walk, not run, on the treadmill immediately for at least 5 minutes to ensure the lubricant is evenly distributed. If you purchase a Lube-N-Walk kit, follow the instructions that come with it to apply the lubrication. 30 XT375 / XT475 / XT675 Before contacting your dealer or Spirit service for aid, please review the following information. It may save you both time and expense. This list includes common problems that may not be covered under the treadmill..s warranty. PROBLEM S O L U TION/CAUSE Display does not light The Safety tether cord not in position. Circuit breaker on front grill tripped or power switch off. Push circuit breaker in until it locks. Plug is disconnected. Make sure plug is firmly pushed into AC household wall outlet. Household circuit breaker may be tripped. Treadmill defect. Contact your SOLE dealer. Treadbelt does not stay centered Treadmill belt hesitates when walked/run on A user may be walking while favoring or putting more weight on either the left or right foot. If this walking pattern is natural, track the belt slightly off-center to the side opposite from the belt movement. See General Maintenance section on Treadbelt Tension. Adjust as necessary. Motor is not responsive / Display is lit If the start button is pressed and the console is functioning, the time display should be counting. If there is an error message showing LS (low speed) try re-calibrating the treadmill (see calibration procedure below). Treadmill will only achieve approximately 7 mph but shows higher speed on display This indicates motor should be receiving power to operate. Low AC voltage to treadmill. Do not use an extension cord. If an extension cord is required it should be as short as possible and heavy duty 14 gauge minimum. Low household voltage. Contact an electrician or your SOLE dealer. A minimum of 110 volt AC, 15 amp is required. Treadbelt stops instantly (it should move High belt/deck friction. See General Maintenance about a foot or so) when tether cord is section on lubrication. pulled while standing on the unit Treadmill trips on board 15 amp circuit Possible High belt/deck friction. See General Maintenance Service Checklist - Diagnosis Guide 31 XT375 / XT475 / XT675 Calibration procedure: 1) Remove the safety key 2) Press and hold down the Start and Fast (speed up) buttons with one hand and replace the safety key with the other. Continue to hold the Start and Fast key until the window displays ..Factory settings.., then press the enter key. 3) You will now be able to set the display to show Metric or English settings. To do this press the up or down key to show which you want, then press enter. 4) Make sure the wheel size diameter is 2.810 (2.98 for XT675) then press enter 5) Adjust the minimum speed (if needed) to 0.5 and then press enter 6) Adjust the maximum speed (if needed) to 12.0 and then press enter 7) Adjust the maximum elevation (if needed) to 15 and then press enter 8) Press start to begin calibration. The process is automatic, the speed will start up without warning so do not stand on the belt. Adjusting the speed sensor: If the calibration does not pass you may need to check the speed sensor alignment. 1) Remove the motor cover hood by loosening the 4 screws that hold it in place (you do not need to remove them completely). 2) The speed sensor is located on the left side of the frame, right next to the front roller pulley (the pulley will have a belt around it that also goes to the motor). The speed sensor is small and black with a wire connected to it. 3) Make sure the sensor is as close as possible to the pulley without touching it. You will see a magnet on the face of the pulley; make sure the sensor is aligned with the magnet. There is a screw that holds the sensor in place that needs to be loosened to adjust the sensor. Re-tighten the screw when finished. Maintenance menu: 1) Press and hold the Start, Stop and Enter key at the same time, until the display shows ..Engineering mode.. (it may say maintenance menu, depending on version). Press the Enter key. 2) You can now scroll through the menu using the up and down keys. Use the Stop key to return to previous menu selection. The menu selections are: 1) Calibration (used to verify calibration) 2) Factory settings (These should not be changed unless instructed by Sole service department) 3) Security (This allows you to lock the console keyboard) 4) Functions i. Sleep (turns sleep mode on or off) ii. Pause (turns pause mode on or off) iii. Maintenance (reset lube message and odometer readings) iv. Units (set display to English or Metric readings) v. Grade return (returns the elevation to lowest setting when pause is pressed) 5) Display test (lights all LED lights for testing) 6) Key test (tests that all keys are functioning) 32 XT375 / XT475 / XT675 Effective October 15, 2007 TREADMILL WARRANTY Spirit Manufacturing Inc. warrants all its home use treadmills.. parts for a period of 5 years fro...
Este manual também é adequado para os modelos :Formadores - XT475 (882.57 kb)
Formadores - XT675 (882.57 kb)