Assessments - 2, GPA: 5 ( )

Fabricante : Keys Fitness Arquivo Tamanho: 4.68 mb Arquivo Nome : bda31211-1f37-4d47-b7dd-baa2ac699e91.pdf Língua de Ensino:

3. Attach the Right Base (1) to the Left Base (25) with two M8 x 78mm Bolts (82), two M8 Washers (98), and two M8 Nylon Locknuts (91). Do not tighten the Locknuts yet. 4. Attach the Center Base (52) to the Right Base (1) with two M8 x 78mm Bolts (82), two M8 Washers (98), and an M8 Nylon Locknut (91). Do not tighten the Bolts yet. Attach the Center Base (52) to the Left Base (25) in the same manner. 2. Insert four M8 x 75mm Carriage Bolts (69) up through the Left Base (25). Note: It may be helpful to place a piece of tape over each bolt head to hold it in place. 1 2 3 4 1 69 25 69 25 25 91 91 98 98 82 82 98 98 98 1 98 82 52 91 1 69 69 Before beginning assembly, make sure you understand the information in the box on page 5. See the PART IDENTIFICATION CHART in the center of this manual for help identifying small parts. Frame Assembly 7 5. See drawing A. Attach the Right Upright (2) to the Right Base (1) with the two indicated M8 x 75mm Carriage Bolts (69) and two M8 Nylon Locknuts (91). Do not tighten the Locknuts yet. See drawing B. Attach the Left Upright (26) to the Left Base (25) with the two indicated M8 x 75mm Carriage Bolts (69) and two M8 Nylon Locknuts (91). Do not tighten the Locknuts yet. 6. Attach the Right Seat Frame (3) to the Right Base (1) with the two indicated M8 x 75mm Carriage Bolts (69) and two M8 Nylon Locknuts (91). Do not tighten the Locknuts yet. Attach the Right Seat Frame (3) to the Right Upright (2) with an M8 x 78mm Bolt (82), an M8 x 96mm Bolt (83), an M8 Washer (98), and an M8 Nylon Locknut (91). Do not tighten the Locknut yet. 5A B 6 2 26 1 25 69 69 91 91 91 91 91 3 82 83 2 98 69 91 91 1 8 7. Attach the Left Seat Frame (27) to the Left Base (25) with the two indicated M8 x 75mm Carriage Bolts (69) and two M8 Nylon Locknuts (91). Do not tighten the Locknuts yet. Attach the Left Seat Frame (27) to the Left Upright (26) with two M8 x 78mm Bolts (82), two M8 Washers (98), and two M8 Nylon Locknuts (91). Do not tighten the Locknuts yet. 8. Orient the Weight Guides (44) with the indicated holes closer to the bottom. Attach the Weight Guides inside of the Center Base (52) with two M8 x 78mm Bolts (82), four M8 Washers (98), and two M8 Nylon Locknuts (91). 7 8 27 82 82 25 26 91 69 91 98 98 91 44 44 Hole Hole 82 82 98 98 98 98 52 91 91 9 9. Slide two Weight Bumpers (45) onto the Weight Guides (44). Slide the eight Weights (55), with the pin holes on the indicated side, onto the Weight Guides. Press the Weight Tube Bumper (46) into the Weight Tube (47). Insert the Weight Tube into the stack of Weights (55). Make sure the pin on the Weight Tube sits in the groove in the top Weight. Grease the indicated holes in the Top Weight (56) with an included grease pack. Slide the Top Weight onto the Weight Guides (44). 10. Attach the Right Top Frame (5) to the Right Upright (2) with two M8 x 78mm Bolts (82), two M8 Washers (98), and two M8 Nylon Locknuts (91). Do not tighten the Locknuts yet. Make sure the Weight Guides (44) are behind the Right Top Frame. 11. Attach a Weight Guide (44) to the Right Top Frame (5) with an M8 x 78mm Bolt (82), two M8 Washers (98), and an M8 Nylon Locknut (91). Do not tighten the Locknut yet. Repeat this step with the other Weight Guide (44). 9 10 11 56 47 46 44 Grease Pin Pin Holes Groove 55 45 5 98 98 82 91 91 2 44 44 82 98 98 91 5 45 44 44 10 12. Attach the Left Top Frame (36) to the Right Top Frame (5) with two M8 x 78mm Bolts (82), two M8 Washers (98), two M8 x 83mm Bolts (112), a Support Plate (31), and four M8 Nylon Locknuts (91). Do not tighten the Locknuts yet. 14. Orient the Butterfly Frame (14) as shown. Attach the Butterfly Frame to the Right Upright (2) with two M8 x 72mm Bolts (85), two M8 Washers (98), and two M8 Nylon Locknuts (91). Do not tighten the Locknuts yet. Attach the Butterfly Frame (14) to the Right Top Frame (5) with two M8 x 78mm Bolts (82), two M8 Washers (98), and two M8 Nylon Locknuts (91). Tighten the M8 Nylon Locknuts (91) used in steps 3–14. 15. Wet the lower end of the Left Butterfly Arm (6) with soapy water. Slide a Large Foam Pad (15) onto the Left Butterfly Arm. Grease an M10 x 90mm Bolt (74) and the indicated edges of two Arm Bushings (23) with a grease packet. Attach the Left Butterfly Arm (6) to the Butterfly Frame (14) with the Bolt (74), an M10 Large Washer (100), the two Arm Bushings, and an M10 Nylon Locknut (90). Make sure the bolt head fits inside of the hole in the Butterfly Frame. Repeat this step with the Right Butterfly Arm (7). 13. Attach the Left Top Frame (36) to the Left Upright (26) with two M8 x 83mm Bolts (112), a Support Plate (31), and two M8 Nylon Locknuts (91)....

Baixe o seu

Para fazer o download, introduza 2 dígitos :