Assessments - 3, GPA: 4 ( )

Fabricante : ParaBody Arquivo Tamanho: 4.68 mb Arquivo Nome : bda31211-1f37-4d47-b7dd-baa2ac699e91.pdf Língua de Ensino:

Make sure the Cable Trap and Finger Guards are oriented as shown. 27 28 29 30 66 99 62 66 90 26 109 111 77 63 99 68 90 66 29 66 70 109 64 66 109 66 99 99 90 25 63 109 63 5 80 68 90 15 31. Attach the end of the Press Cable (109) to a “U”- bracket (50) with an M8 Washer (98) and an M8 Nylon Locknut (91). Note: Do not completely tighten the Locknut; it should be tightened so that only two threads of the Cable show past the Locknut, as shown in the inset drawing. 33. Wrap the Butterfly Cable (106) over a “V”-pulley (62). Attach the “V”-pulley, a Large Cable Trap (111), an M10 Washer (99), and two Full Finger Guards (104) to the Right Upright (2) with an M10 x 62mm Bolt (73) and an M10 Nylon Locknut (90). 34. Wrap the Butterfly Cable (106) under a 90mm Pulley (63). Attach the Pulley and two Half Finger Guards (66) to the Double “U”-bracket (61) with an M10 x 48mm Bolt (84) and an M10 Nylon Locknut (90). Make sure the Finger Guards are oriented as shown. 35. Wrap the Butterfly Cable (106) over a “V”-pulley (62). Attach the “V”-pulley, a Large Cable Trap (111), an M10 Washer (99), and two Full Finger Guards (104) to the Right Upright (2) with an M10 x 62mm Bolt (73) and an M10 Nylon Locknut (90). 32. Locate the Butterfly Cable (106). Grease an M8 x 22mm Shoulder Bolt (39). Attach the Cable to the Left Butterfly Arm (6) with the Bolt and an M8 Nylon Locknut (91). Make sure the flat edge of the Cable is against the Butterfly Arm. 31 32 33 34 35 50 91 98 109 39 91 6 106 Grease Flat Edge 90 90 66 66 61 84 2 104 104 106 106 111 62 73 99 63 90 2 104 104 106 111 62 73 99 91 109 16 36. Grease an M8 x 22mm Shoulder Bolt (39). Attach the Butterfly Cable (106) to the Right Butterfly Arm (7) with the Bolt and an M8 Nylon Locknut (91). Make sure the flat edge of the Cable is against the Butterfly Arm. 38. Wrap the Short Cable (108) over* a 90mm Pulley (63). Attach the Pulley and two Half Finger Guards (66) to the Double “U”-bracket (61) with an M10 x 48mm Bolt (84) and an M10 Nylon Locknut (90). Make sure the Finger Guards are oriented as shown. 40. Locate the Weight Cable (110). Route the Cable up through the Right Top Frame (5) and over a 90mm Pulley (63). Attach the Pulley inside the Top Frame with an M10 x 80mm Bolt (75), two M10 Washers (99), two M10 x 19mm Spacers (102), and an M10 Nylon Locknut (90). 39. Attach the end of the Short Cable (108) to a “U”- bracket (50) with an M8 Washer (98) and an M8 Nylon Locknut (91). Note: Do not completely tighten the Locknut; it should be tightened so that only two threads of the Cable show past the Locknut, as shown in the inset drawing. 37. Locate the Short Cable (108). Attach the Cable to the M8 x 96mm Bolt (83) used in step 6 with an M8 Washer (98), an M8 x 13mm Spacer (103), and an M8 Nylon Locknut (91). 36 37 39 40 38 91 91 39 91 7 106 Grease 83 98 91 103 108 63 84 66 61 90 66 108 50 98 108 108 63 5 99 99 75 90 110 102 102 2 Flat Edge 17 41. Route the Weight Cable (110) over a 90mm Pulley (63) and down through the Right Top Frame (5). Attach the Pulley inside the Top Frame with an M10 x 80mm Bolt (75), two M10 Washers (99), two M10 x 19mm Spacers (102), and an M10 Nylon Locknut (90). 43. Wrap the Weight Cable (110) over a 90mm Pulley (63). Attach the Pulley to the indicated bracket on the Right Top Frame (5) with an M10 x 45mm Bolt (80) and an M10 Nylon Locknut (90). 44. Wrap the Weight Cable (110) over a 90mm Pulley (63). Attach the Pulley and a Cable Trap (68) to the indicated bracket on the Right Top Frame (5) with an M10 x 45mm Bolt (80) and an M10 Nylon Locknut (90). Make sure the Cable Trap is oriented to hold the Cable in the groove of the Pulley. 45. Set the M12 Washer (33) on top of the Weight Tube (47). Thread the M12 Nut (49) all the way onto the Weight Cable (110). Thread the Weight Cable (110) into the Weight Tube (47) a couple of turns. 42. Wrap the Weight Cable (110) under a 90mm Pulley (63). Attach the Pulley, a Cable Trap (68), and two Half Finger Guards (66) at the second hole from the top of the two Pulley Plates (51) with an M10 x 52mm Bolt (78) and an M10 Nylon Locknut (90). Make sure the Cable Trap and Finger Guards are oriented as shown. 41 42 43 5 Bracket 44 45 5 63 90 99 99 75 102 110 63 90 78 110 66 66 68 51 51 90 80 63 110 5 Attach pulley Bracket on this side 80 63 68 90 110 47 33 49 110 18 46. Locate the Ab Cable (107). Route the small ball on the Cable through the Leg Lever (4) and the Right Seat Frame (3). Make sure the Cable is over the rod in the Seat Frame. Attach a 90mm Pulley (63) inside the Leg Lever (4), over the Ab Cable (107), with an M10 x 65mm Bolt (77), two M10 Washers (99), two M10 x 12mm S...

Baixe o seu

Para fazer o download, introduza 2 dígitos :