Assessments - 2, GPA: 3
(
)
)
|
Facilidade de uso
WHEN PROPERLY POUNDED TOGETHER, THE POLE SECTIONS SHOULD HAVE A 3-1/2" MINIMUM OVERLAP, LEAVING 1-1/2" BETWEEN THE OVERLAPPING POLE AND THE IDENTIFICATION STICKER. CAUTION! ID# M6711041 02/07 14 5. Install bolt (12) through bracket and bottom pole section (6) and secure with nut (10) as shown. Nut should be tightened until flush (even) with locknuts outer edge. 12 10 6 6. 6 Install rod (9) through bottom pole section (6) as shown. Install large eye bolts (7) onto rod (9) as shown. 9 7 9 7 Secure cover to rod (9) using washers (45) nuts (8) and 7. nut covers (13) as shown. 138 45 15 02/07 ID# M6711041 8. 8. Install pole mount bracket (15) and reinforcement bracket (42) with carriage bolts (16) as shown. Tighten flange nuts (14) completely. 4 42 16 16 15 14 14 9. Attach spacers (20, 21) to pole mount bracket (15) with bolts (19), washers (17), and nuts (8) as shown. 15 17 17 8 19 17 17 21 20 20 21 IMPORTANT! Tighten just until washers (17) stop moving. ID# M6711041 02/07 16 17 02/07 ID# M6711041 Assemble lanyard (25) to locking pin (24) as shown (FIG A). Attach covers (22) onto pole mount bracket (15) with carriage bolt (23) and nut (14) as shown. 10. 15 14 24 22 22 25 23 FIG. A 25 24 Loop end of pin lanyard (25) over carriage bolt (23) as it passes through the pole mount bracket (15) during this assembly. IMPORTANT! 23 25 24 Insert handle assembly (3) through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05 m) mark with pin (24). 24 11. 3 SECTION B: ATTACH THE BACKBOARD This is what your system will look like when you’ve finished this section. TOOLS REQUIRED FOR THIS SECTION Phillips-Head Screwdriver 9/16”1/2” (2) 1/2”, (2) 9/16", and (2) 3/4” Wrenches (2) Socket Wrenches and Sockets AND/OR 3/4” Sawhorse or Support Table 35 32 Upper Elevator tube Lower Elevator tube Identify elevator tubes. ID# M6711041 02/07 18 1. 1. Assemble backboard brackets (27) using bolts (47), and nuts (8) as shown. 27 47 8 8 47 19 02/07 ID# M6711041 2. Attach lower elevator tubes (32) and counter balance spring (33) to backboard support brackets (27) using spacers (11, 26), bolt (29), and nut (31) as shown. Insert T-bolt (49) into rim bracket (48) then, attach that assembly to board using bolts (44) and nuts (14) 32 32 27 3. 29 32 32 26 26 14 14 3127 33 49 48 48 44 11 ID# M6711041 02/07 20 21 02/07 ID# M6711041 4. 50 52 1 48 49 Install Slam Jam Rim to Backboard 34 51 49 1 52 A B C D E A Fit rim (34) securely into bracket (48) as shown. Allow T-bolt (49) to slip through center hole in rim (34). B Install reinforcement bracket (50) onto T-bolt (49) as shown. C Install spring (51) onto T-bolt (49) as shown. D Install special nut (52) and washer (1) onto T-bolt (49). E Tighten nut (52) until flush with end of T-bolt (49). 49 49 5. 5. Attach upper elevator tubes (35) to backboard support brackets (27) using spacers (26 & 11), bolt (29), and nut (31) as shown. 35 35 26 31 29 26 27 11 31 31 40 38 32 4 37 37 29 30 32 30 6. Support pole on sawhorse. Attach backboard assembly to top pole section (4) as shown. Install pole cap (38). Use caution; elevator assembly is heavy. USE CAUTION; ASSEMBLY IS HEAVY. TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! ID# M6711041 02/07 22 23 02/07 ID# M6711041 29 29 32 35 31 31 35 30 30 37 36 36 7. Install upper elevator tubes (35) to triangle plates (37) as shown. Install handle assembly (3) to lower elevator tubes (32) using bolt (29), spacers (36), and nut (31) as shown. 4 Before going on to next step, set adjustable system assembly to the 10’ (3.05 m) setting. NOTE: 3 8. Insert bolt (29) through left side upper elevator tube (35), then stretch spring (33) onto bolt (29). Insert bolt (29) through right side upper elevator tube (35) and secure with nut (31). 35 33 31 35 3 29 33 USE EYE PROTECTION WHEN INSTALLING SPRINGS. WARNING! Install net (43) as shown. B. D.C. A. 34 43 9. B. D.C. A. 34 43 9. 10. Roll completed assembly to desired position. Fill tank with water (approx. 34 gallons (129 Liters)) or sand (approx. 280 lbs. (128 kg)) and snap cap (41) in place. 41 IF USING SAND: 2 GALLONS OF ANTI-FREEZE IS NOT REQUIRED NOTE: SANDSAND(280 lb.)(280 lb.)(128 kg)(128 kg)ADD TWO GALLONS (7.6 LITERS) OF NON-TOXIC ANTIFREEZE IN SUBFREEZING CLIMATES. CAUTION! DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY; IT MAY TIP OVER. WARNING! ID# M6711041 02/07 24 25 02/07 ID# M6711041 1. Apply height adjustment and moving label (46) to front of pole as shown. 2. A. While holding handle, remove pin (24). B. Move elevator up or down to desired height. C. Replace pin (24) full length to lock system at desired height. SECTION C: APPLY HEIGHT AND MOVING LABEL & HEIGHT ADJUSTMENT 10 ft. 46 (3.05 m) 24 A. B. C. DO NOT ALLOW CHILDREN TO ADJUST HEIGHT. WARNING! Peel protective film from surface of acrylic backboard prior to use. NOTE: TWO CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD ...