Assessments - 4, GPA: 4.5
(
)
)
|
Facilidade de uso
B Place LOCK WASHER (E) and BOLT (D) into flat side of LEFT upright MAST and tighten. C Place ARC WASHER (F) and BOLT (D) into curved side of LEFT upright MAST and tighten. * Be sure to tighten bolts after all are lined up. A Gently lift RIGHT side of the console to connect the CONSOLE CABLE. Carefully tuck wires in mast to avoid damage. NOTE: Do not pinch console cable or grip pulse wires. B Repeat steps 2-3 above to assemble the right side upright mast and console. IMPORTANT INTRODUCTION ASSEMBLY PRECAUTIONS BEFORE YOU BEGIN TREADMILL OPERATION CONDITIONING GUIDELINES TROUBLESHOOTING & MAINTENANCE LIMITED WARRANTY 9 ASSEMBLY STEP 3 ASSEMBLY STEP 4 INTRODUCTION IMPORTANT PRECAUTIONS ASSEMBLY BEFORE YOU BEGIN TREADMILL OPERATION LIMITED WARRANTY 8 DO NOT CUT STRAPS UNTIL STEP 1.4!* Disassemble box and remove the cardboard packaging that is not beneath the treadmill. Do not attempt to lift the treadmill at this time. Reach under treadmill running deck to locate parts box. Remove plastic wrap from console masts. NOTE: It is recommended that you apply grease to the threads of each bolt as you assemble your treadmill, to prevent loosening and noise. Also, during each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt. Lift LEFT CONSOLE MAST into upright position. Be sure to hold the console mast firmly, as it will not stay in the upright position on it’s own. Move LEFT SIDE LINKAGE ARM into position. Insert TEFLON WASHER (B) (2 pcs) and BOLT (A) and tighten. Repeat on the right side. Now cut the banding straps and remove remaining packaging material.* Lift the RUNNING DECK until lock latch is fully engaged. Remove CONSOLE from box and place out of the way. Lower the treadmill RUNNING DECK from the folded position by stepping on LOCK LATCH on lower right side. ASSEMBLY STEP 1 ASSEMBLY STEP 2 A B C D A B C PRE-ASSEMBLY TROUBLESHOOTING & MAINTENANCE CONDITIONING GUIDELINES * NOTE: If the straps have been removed before completing STEP 1, refer to the TROUBLESHOOTING section (page 26) in order to restore the treadmill to its proper position. LEFT CONSOLE MAST LEFT SIDE LINKAGE ARM BOLT A 1 3 2 ...... .................... .............. .............. ........ ................ ........ .................... ASSEMBLED IN STEP 3 WARNING CST3.5-4.5 Treadmill Rev0.2.indd 8-9 4/21/05 11:22:36 AM 10 INTRODUCTION IMPORTANT PRECAUTIONS ASSEMBLY BEFORE YOU BEGIN TREADMILL OPERATION LIMITED WARRANTY TROUBLESHOOTING & MAINTENANCE CONDITIONING GUIDELINES BEFORE YOU BEGIN ASSEMBLY 11 IMPORTANT INTRODUCTION PRECAUTIONS TREADMILL OPERATION CONDITIONING GUIDELINES TROUBLESHOOTING & MAINTENANCE LIMITED WARRANTY A Slide the HANDLEBAR SLEEVE onto the bottom of the HANDLEBAR EXTENSION. B Slide the HANDLEBAR EXTENSION onto the CONSOLE HANDLEBAR. C Insert BOLTS (?) into HANDLEBAR EXTENSION. D Insert BOLT (?) through bottom hole of HANDLEBAR EXTENSION into CONSOLE MAST. E Tighten all HANDLEBAR EXTENSION bolts. F Slide HANDLEBAR SLEEVE all the way down on HANDLEBAR EXTENSION to cover BOLT (?). G Repeat on other side. A Slide the LONG HANDLEBAR EXTENSION onto the CONSOLE HANDLEBAR. B Insert BOLTS (?) into LONG HANDLEBAR. C Align the lower part of the LONG HANDLEBAR with the center of the CONSOLE MAST. D Insert BOLTS (?) through bottom holes of LONG HANDLEBAR into CONSOLE MAST. E Tighten all LONG HANDLEBAR bolts. F Repeat on other side. ASSEMBLY STEP 5-B (CST4.5 model) ........ .................. .............. .................. .................. .................. .............. ........ ASSEMBLY STEP 5-A (CST3.5 model) .................. .................. .................. ............ ................ .................. ........................ .............. .................. A Slide PLASTIC COVER CAPS over SUPPORT BARS. B Slide SUPPORT BARS into side MOUNTING BRACKETS and line up with top MOUNTING BRACKETS. C Insert 2 BOLTS (?) into the tops and 2 BOLTS (?) into the bottoms of each SUPPORT BAR. D Slide PLASTIC COVER CAPS down to cover BOLTS (?). E Connect power plug to the treadmill and connect the cord to a power outlet. The on/off switch is located next to the power cord. Flip this switch to the 'on' position, so that the switch is lit. You will hear a beep and the console will light up. ASSEMBLY STEP 6 .................................... ...................... ................ .............. .................. .................. YOU’RE FINISHED! POWER SWITCH CIRCUIT BREAKER CST3.5-4.5 Treadmill Rev0.2.indd 10-11 4/21/05 11:22:41 AM INTRODUCTION BB EE FF OO RR EE YY OO UU BB EE GG II NN INTRODUCTION IMPORTANT BEFOREYOU BEGINBEFOREYOU BEGIN TREADMILL CONDITIONING TROUBLESHOOTING LIMITED ASSEMBLY PRECAUTIONS OPERATION GUIDELINES& MAINTENANCEWARRANTY CONGRATULATIONS! on choosing your treadmill. You’ve taken an important step in developing and sustaining an exercise program! Your treadmill is a tremendously effective tool for achieving your personal fitness g...
Este manual também é adequado para os modelos :Formadores - CLUB SERIES CST4.5 (1.74 mb)