Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
If you have extremely hard water, alternate between tap water and distilled water for use in the iron. 5 840125000 ENv01.qxd 12/14/04 3:04 PM Page 6 Features (on selected models) Automatic Steam Provides the correct amount of steam for the fabric selected. Set Temperature Control to the number that matches the number on the Fabric Setting Chart. Blast of Steam and Spray Buttons Push Blast of Steam Button for an extra blast of steam. Push Spray Button to release a fine spray of water for difficult wrinkles in cotton or linen. Spray Steam Power On Light Models that do not have the automatic shutoff and the reset button, do have a power light. This light comes on when Power the iron is plugged in. The light will On Light remain on even if the Temperature Control is turned to OFF ( O ) . The light will stay on until iron is unplugged. 6 Features (continued) Auto Shutoff Status Indicator and Auto Shutoff Reset Button Status Indicator If the iron is an Automatic Shutoff model, the light comes on when the iron is first plugged in. After 1 hour the Reset iron will shutoff and the light will go out. Button Push the Reset Button to turn the iron back on for another hour of ironing. Vertical Steam 1. Follow Steps 1 through 3 in “To Steam Iron.” 2. Hang garment in a location that is not susceptible to damage from heat or moisture. Do not hang in front of wallpaper, window, or mirror. 3. Hold iron about 6 inches away from garment and press and release the Blast Button to steam out wrinkles. Do not press Blast Button more than once every 2 seconds. 4. To turn iron off, turn Temperature Control to OFF ( O). Unplug iron. 5. Empty water from the iron following directions in “Caring for Your Iron.” NOTE: Do not allow hot soleplate to touch delicate garments. 7 840125000 ENv01.qxd 12/14/04 3:04 PM Page 8 Fabric Setting Chart Steam Setting To Iron Ironing Instructions 0 Off O 1 Nylon Dry iron on the wrong side of the fabric. 2 Acrylic Dry iron on the wrong side of the fabric. 2 Silk Dry iron on the wrong side of the fabric. 3 Polyester Iron with fabric still damp. 4 Rayon Iron on the wrong side of fabric. 4 Wool Steam iron on the wrong side of fabric. 5 Cotton Iron while still damp using steam and/or spray. 6 Linen Iron on wrong side of fabric while still damp. 8 Caring for Your Iron Iron 1. Turn Temperature Control to OFF ( O ) . The Water Tank of your iron should be emptied after each use. Unplug iron and hold over a sink. Turn iron upside down until Water Tank Opening is parallel with sink. Water will run out of water tank opening. 2. After iron has completely cooled, wrap cord loosely around iron and store in an upright position. Do not store iron laying flat on soleplate. Soleplate 1. Never iron over zippers, pins, metal rivets, or snaps, as these may scratch the soleplate. 2. To clean occasional build-up on the soleplate, wipe with a sudsy cloth. Do not use abrasive cleansers or metal scouring pads. 3. Always store iron upright in the heel rest position. 9 840125000 ENv01.qxd 12/14/04 3:04 PM Page 10 Caring for Your Iron Troubleshooting Self-Clean To keep the steam vents clear of any build-instructions each time you iron using steam. 1. Unplug iron. Turn Temperature Control to OFF ( O ). Fill iron with water to 1. 2 of its maximum capacity. 2. Plug in iron. With iron in an upright position, turn Temperature Control to Linen setting and let iron heat for 2 minutes. 3. Turn Temperature Control to OFF ( O ). Unplug iron and hold over a sink with soleplate facing down. 4. Press and hold the Self Clean Button. Boiling water and steam will flow out of steam vents. Allow all water to drain from iron. 5. Gently move iron front to back to allow water to clean entire soleplate area. 6. If water still remains inside of soleplate, reheat iron as indicated in Step 2. Boiling water and steam could still flow out of steam vents. PROBLEM THINGS TO CHECK Won’t heat • Is the iron plugged in and the outlet working? Check the outlet by plugging in a lamp. • Is the Temperature Control turned to a fabric setting? • If automatic shutoff model, is light on? If not, press Reset Button. Water is leaking • Do not overfill the water tank. • If steam ironing, did the iron have enough time to preheat? • If dry ironing with Temperature Control on steam setting, empty water from water tank. Won’t steam • Check the water level. • Has the iron had enough time to preheat? Leaves spots • ALWAYS empty the water tank of the iron after using. Water left in the tank may discolor clothing and soleplate. Twisted cord • If the iron cord should become twisted, unplug iron and let cool. Hold iron cord in the middle of entire length. Let plug and iron dangle freely until cord uncoils. This will extend the life of your iron cord. 10 11 840125000 ENv01.qxd 12/14/04 3:04 PM Page 12 Customer Service If you have a question about your iron, call our toll-free customer service number. Before calling, please note the model, type, and series numbers and fill in that informat...