|
Facilidade de uso
If the iron does not steam, gently tap the soleplate on the ironing surface. Placing the iron on its heel in an upright position interrupts the flow of steam. 8. When finished, turn temperature control dial to OFF and variable steam dial to OFF, and unplug. Allow to cool before cleaning the exterior of the iron and storing. CAUTION HOT SURFACES: Avoid coming in contact with escaping steam. Filling The Water Tank 1. Unplug the iron before filling. 2. Turn the variable steam dial to OFF. 3. Hold the iron in the horizontal position (see Figure 2). 4. Using a measuring cup, slowly pour water into the water fill opening (see Figure 2). 5. Check see-through water tank to see if iron is filled to maximum fill line (see Figure 3). Note: Your iron is designed to use tap water. DO NOT use water from home water softening systems because such water may contain minerals that may harm the iron. 5. Emptying The Water Tank The water tank should be emptied after each use. To do so: 1. Unplug the iron from the electrical outlet. 2. While the iron is still warm, hold the iron over a sink and allow the iron to drain by tipping the point of the iron down. 3. Gently shake the iron to loosen any water drops that may be trapped. The warmth of the iron should dry out any remaining water. Note: If you empty the water tank after the iron has cooled, set the iron in an upright position on its heel, plug it in and set the temperature dial to maximum heat for 2 minutes. Turn temperature control dial to OFF and variable steam dial to OFF, and unplug. Let iron cool before storing it. Flushing Flushing the iron is advised after every 5 usages to prevent harmful mineral build-up that can clog the iron and prevent it from heating and steaming properly. To flush the iron: 1. Position temperature control dial to OFF. 2. Turn variable steam dial to OFF. 3. Fill the iron’s water tank to its maximum fill line. 4. Plug the iron in and set the temperature control dial to Linen. Let it heat for 2 minutes. 5. Turn the variable steam dial clockwise to the MAX setting. 6. Place a hand towel over the ironing surface. 7. Hold the iron horizontally 2 inches above the towel allowing steam to flow through the vents until the water tank is emptied. 8. Pass the iron over a damp cloth to clean the soleplate. 9. When finished, turn temperature control dial to OFF and variable steam dial to OFF and unplug. Allow iron to cool before cleaning the exterior of the iron or storing. Use a cloth to wipe off exterior of iron before storing. 6. Steam and Dry Iron Use and Care Guide Storing The Iron Storing The Iron User Maintenance Instructions This appliance requires little maintenance. It contains no user serviceable parts. Do not try to repair it yourself. Refer it to a qualified appliance repair techinician if servicing is needed. Care And Cleaning CAUTION: Unplug the iron from the electrical outlet before cleaning the exterior of the iron and storing. Never immerse an appliance in water. To protect the soleplate from scratching, avoid ironing over snaps, zippers, metal buttons, etc. Also, do not place the iron on metal or rough surfaces. If starch or other residues cling to the soleplate, use hot iron cleaner according to directions. Hot Iron Cleaner is available at mass merchandise, discount or hardware stores. A “home remedy” for cleaning starch or other material buildup on the soleplate is as follows: 1. Unplug the iron and allow to cool completely. 2. Mix together 4 tablespoons baking soda and 1 tablespoon water. 3. Apply mixture to the soleplate with a soft cloth. 4. Clean mixture off with a water dampened clean cloth, dry thoroughly. Note: DO NOT put any chemical cleaning agents or solvents in the water tank. 7. LIMITED ONE-YEAR WARRANTY LIMITED ONE-YEAR WARRANTY To return the appliance, ship to: To contact us, please write to, call, or email: ATTN: Repair Center Consumer Relations Department 708 South Missouri Street PO Box 7366 Macon, MO 635...
Este manual também é adequado para os modelos :Irons - 3302 (259.02 kb)
Irons - 3302CAN (259.02 kb)