Assessments - 1, GPA: 4
(
)
)
|
Facilidade de uso
• If an extension cord is absolutely necessary, a 15-ampere cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the extension cord so that it cannot be pulled or tripped over. FOR PRODUCTS PURCHASED IN THE UNITED STATES AND CANADA To reduce the risk of electrical shock, this appliance has a polarized plug (one blade is wider than the other). This plug fits a polarized outlet only one way; if the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature. SAVE THESE INSTRUCTIONS IRONING GUIDE FABRIC SUGGESTED STEAM SETTING FABRIC SELECT DIAL SETTING IRONING RECOMMENDATIONS Acrylic O/Off (Dry) Synthetic Iron garment inside out Acetate O/Off (Dry) Synthetic Iron garment inside out while still damp. Polyester O/Off (Dry) Synthetic Iron garment inside out while still damp. Rayon O/Off (Dry) Synthetic Iron garment inside out. Silk O/Off (Dry) Silk Iron garment inside out. Use an ironing cloth* to prevent shine marks. Viscose O/Off (Dry) Silk Mainly dry iron; steam may be used under garment manufacturer’s instructions. Nylon O/Off (Dry) Silk Iron garment inside out while still damp. Wool Steam Wool Iron garment inside out or use an ironing cloth.* Wool Blends Steam Wool Iron garment inside out or use an ironing cloth.* Cotton Blends Steam Cotton Follow garment manufacturer’s instructions. Use setting for the fiber requiring the lowest setting. Corduroy Steam Cotton Iron garment inside out or use an ironing cloth* and then brush the garment with your hand to raise the texture of the fabric. Cotton Steam Cotton Iron dark fabrics inside out to prevent shine marks. Linen Steam Linen Iron garment inside out or use an ironing cloth* to prevent shine marks (especially on dark fabrics). Denim Steam Linen Use the SPRAY MIST® feature and/or the SHOT OF STEAM® for deeper penetration to remove wrinkles. *An ironing cloth is a cotton, dry-cleaned cloth that you place over the garment you are ironing to prevent the fabric from looking shiny. Note: Some fabrics may require more steam than others. Your iron has the capability to adjust steam as needed. FEATURES OF YOUR CLASSIC IRON 7 9 8 5 6 3 4 2 1 107 9 8 5 6 3 4 2 1 10 1. SPRAY MIST® Release 2. Covered Water Fill Hole 3.Steam Lever 4. SPRAY MIST® Button 5. SHOT OF STEAM® / Vertical Steam Button (select models only) 6. Power Indicator Light / MOTION SMART® Auto-Off Indicator (select models only) 7. Fabric Select Slide 8. See-Through Water Reservoir 9. Soleplate 10. Self-Clean Button TO FILL THE WATER RESERVOIR 1. Make sure the iron is unplugged. Set the Steam Lever to O/Off (Dry) and the Fabric Select Slide to OFF. 2. Lift the Water Fill Hole Cover. 3. Fill water cup with water. Pour water into iron water reservoir. Do not fill water reservoir beyond maximum fill level. WARNING: To prevent the risk of burns, be careful when filling a hot iron with water. Hot metal parts, hot water and steam can cause injuries. DRY IRONING 1. Make sure the Steam Lever is turned to the O/Off (Dry) setting. 2. Plug the cord into a 120-Volt AC outlet. 3. Select the fabric setting you desire using the slide (Silk or Synthetics). Allow the iron to heat for 2 minutes. While the iron is heating, make sure it is sitting on its heel rest on a stable, protected surface. NOTE: While the Steam Lever is turned to the O/Off (Dry) setting, you may still use the SHOT OF STEAM® or SPRAY MIST® feature. Please make sure the water reservoir is 1/4 full of water. TIP: Refer to the Ironing Guide for the recommended setting for your fabric. STEAM IRONING 1. Make sure the Steam Lever is turned to the O/Off (Dry) setting. (This Step is not necessary for Irons with the Drip Free™ feature) 2. Follow the instructions for “Filling the Water Reservoir”. 3. Plug the cord into a 120-Volt AC outlet. 4. Select the fabric setting you desire using the slide (Synthetic, Silk, Linen, Cotton or Wool). Allow the iron to heat for 2 minutes. While the iron is heating, make sure it is sitting on its heel rest on a stable, protected surface. 5. Allow the iron to heat for 2 minutes, and then turn the Steam lever to the appropriate setting. TIP: Refer to the Ironing Guide for the recommended setting for your fabric. IMPORTANT: When not ironing, always set the Steam Lever to O/Off (Dry) and the Fabric Slide to OFF. USING THE IRON’S SPECIAL FEATURES SPRAY MIST® FEATURE The SPRAY MIST® feature is a powerful water spray mist that dampens the fabric to aid in removing wrinkles from heavy fabrics and for setting creases. To use the SPRAY MIST® Feature: Press the SPRAY MIST® button firmly. SHOT OF STEAM® FEATURE (select models only) The SHOT OF STEAM® feature provides an extra burst of steam for deep penetration of stubborn wrinkles. You can use this feature while Dry or Steam ironing, but the water reservoir must be at least 1/4 full of water. To use the SHOT OF STEAM® Feature: Place the iron on top ...
Este manual também é adequado para os modelos :Irons - 3964 (114.63 kb)
Irons - 3966 (114.63 kb)