Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
• Use iron only for its intended use. • To protect against electric shock, do not immerse the iron in water or other liquids. • The iron should always be turned off before plugging into or unplugging from an outlet. Never yank cord to disconnect from outlet; instead grasp plug and pull to disconnect. • Do not allow cord to touch hot surfaces. Let iron cool completely before putting away. Loop cord loosely around cord wrap when storing. • Always disconnect iron from electrical outlet when filling with or emptying of water, and when not in use. • Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged in any manner or dropped into water. To avoid the risk of electric shock, do not disassemble the iron or replace supply cord. For service information see warranty page. • Close supervision is necessary for any appliance being used by or near children. • Do not leave iron unattended while connected or on an ironing board. Always position iron carefully to prevent it from falling if ironing board is accidentally moved or cord is pulled. Always use heel rest. • Burns can occur from touching hot metal parts, hot water, or steam. Use caution when you turn a steam iron upside down or use the surge of steam – there may be hot water in the water tank. Avoid rapid movement of iron to minimize hot water spillage. • To reduce the risk of contact with hot water emitting from the steam vents, check appliance before each use by holding it away from body and operating steam button. SPECIAL INSTRUCTIONS: • To avoid a circuit overload, do not operate another high wattage appliance on the same circuit. • While use of an extension cord is not recommended, if you must use one, make sure the cord has the same or higher wattage as the appliance (wattage is stamped by the soleplate of the unit). Position the extension cord so that it cannot be pulled or tripped over. SAVE THESE INSTRUCTIONS POLARIZED PLUG – This appliance may have a polarized plug –one blade is wider than the other. To reduce the risk of electric shock, this plug is intended to fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in any way. 1. Never pull or yank on cord or the appliance. 2. To insert plug, grasp it firmly and guide it into outlet. 3. To disconnect appliance, grasp plug and remove it from outlet. 4. Before each use, inspect the line cord for damage. If damage is found, do not use appliance. 5. Let iron cool completely before wrapping cord. Never wrap the cord tightly around the appliance as this could place undue stress on the cord where it enters the appliance and cause it to fray and break. DO NOT OPERATE APPLIANCE IF THE LINE CORD SHOWS ANY DAMAGE OR IF APPLIANCE WORKS INTERMITTENTLY OR STOPS WORKING ENTIRELY. SPECIAL ATTENTION: This appliance is designed with a protective coating around the heating elements. When plugged in and operating for the first time, there may be momentary smoking while this coating is initially heated. This represents no danger to the user and does not indicate a defect in the unit. When using for the first time, allow the appliance to continue heating until the smoke dissipates. This should last only about 30 seconds. OPERATING INSTRUCTIONS Before using the first time: Remove any sticker or protective foil from the soleplate. Preheat; move iron over an old cloth several times to remove any residue from the soleplate. A – Spray Nozzle B – Water Filling Opening C – Steam Control Knob D – Steam Button E – Spray Button F – Fabric/Temperature Dial G – Fill Indicator H – Power Indicator Light I – Auto-off Indicator E D C B A G F I H D E C B A G F H I To Use Iron: Always check the ironing instructions on the garment label first. Sort the fabrics according to the ironing temperature. The iron will take less time to heat up than to cool down therefore clothes such as synthetic fabric, silk, etc. with lower ironing temperatures should be ironed first. Clothes with higher ironing temperatures such as wool, cotton and linens should be ironed last. If you are unsure of the fabric, test by ironing a hidden area such as an inside seam or edge. If the iron drags or the fabric changes color, lower the temperature and/or use a pressing cloth. For blended fabrics, always use the lower setting. For example, a garment with 60% nylon and 40% wool should be set at the temperature indicated for nylon. Always test by ironing a hidden area. 1. Stand iron vertically on its heel and set the Thermostat Dial to the “MIN” position. 2. Plug appliance into electrical outlet, 120 volt, AC only. Rotate the Thermostat Dial to the desired fabric selection. The Power Indicator Light will come on indicating iron is heating. When the Power Indicator Light goes out the iron has reached set temperature and you may begin ironing. To Fill Water Tank...
Este manual também é adequado para os modelos :Irons - J613W. (115.9 kb)