Assessments - 4, GPA: 4.5
(
)
)
|
Facilidade de uso
The following precautionary measures should be observed in order to ensure proper installation: a) Hoods must be installed in compliance with the required specifications contained in the instruction manual for the hood itself. b) The built-in ceramic glass top can be installed on any counter top as long as it is 600 mm or more in width and resistant to temperatures of up to 100°C. The dimensions and the position of the hole are shown in fig.. Insert the hob into the hole, pressing firmly around the frame to make it adhere to the counter top. Important: The surface where the hob is installed must be perfectly flat. Deformations caused by improper installation may affect the characteristics of the hob, and, therefore, its performance. c) If a wooden panel is installed beneath the hob for insulation purposes, it must be positioned at least 20 mm from the bottom part of the hob itself. Note: If the hob is installed above a built-in oven, it is preferable that the oven be installed in such a way that it is set on two strips of wood; if, on the other hand, the oven is installed on a continuous base, there must be an opening in the back of at least 45 x 560 mm. 560 mm. 45 mm. 575 mm. 505mm. 39 mm. 48 mm. 490mm. +0 -2 If the hob is installed above a built-in oven equipped with a forced air cooling system, air intake and exhaust slots must be provided to ensure that the air circulates properly within the cabinet. Figures provide illustration of possible 560 mm. +0 -2 installation solutions. X (CEI 335-2-6) These measurements must absolutely be observed in so far as improper installation can cause the surrounding surface areas to overheat. It is recommended that the hob be installed at a distance of at least 40 mm from the back wall or other vertical surfaces to ensure that the air circulates properly over the cooking area and to avoid overheating the surrounding surfaces. A seal or gasket is provided with the hob; make sure that it adheres properly to the bottom part of the frame of the hob. The seal must fit properly around the entire hob frame and especially along the corners in order to create a seal between the counter top and the cooktop itself so as to prevent spills or splashes from leaking into the cabinet below. Fasten the 4 hooks supplied into the slots as shown in Fig.; Fastening diagram for the hooks A A A A 3040 Fastening positions Hook placement for 40 and 30 mm tops 9 Electrical Connection - Model E600 Electrical Connection THIS APPLIANCE MUST BE EARTHED. The installation procedure must be carried out by a qualified electrician. The electrical safety of this appliance is guaranteed only if the appliance is correctly earthed in compliance with the standards of electrical safety. The manufacturer can under no circumstances be considered responsible for any damage that might occur due to incorrect earthing of the hob. The electric hob is not supplied with a power supply chord because the type of chord used depends on the type of electrical connection (see the following connection diagram). Open the terminal box following the instructions illustrated in the diagram below: 2 1 1 2 3 4 5 V To connect the supply cord, proceed as follows: -Loosen the screws on the wire clamp "V", as well as the screws for the contacts. - Insert the wires beneath the contact screws, as shown in the diagram and tighten them. - Fasten the cord with the appropriate wire clamp and close the cover. Electrical Connections: 1 2 3 4 5 Fuse 32 A L N Voltage and frequency of power supply: 230-240V 50-60Hz 5700W Connecting the supply cord to the electrical mains: The hob must be connected to a double pole mains switch which must be installed between the appliance and the mains.. The double pole mains switch must have a minimum of 3mm of space between the contacts, be sized to the load and comply with current regulations (the switch must not be able to disconnect the earth conductor). The supply cord should conform to BS6004 conductor size 4mm2 and must be positioned so that no part of it reaches a temperature of 50°C higher than room temperature. Before making the connection, make sure that: • the limiter switch and the residual wiring can support the appliance load (see the rating plate). • the mains system is properly earthed in compliance with current regulations and provisions. • there is easy access to the socket or the double pole mains switch after the appliance is installed. IMPORTANT: If the hob is installed above a built-in oven, the electrical connection for the hob must be independent of that for the oven, both for safety reasons and to facilitate the removal of the oven for maintenance, repair etc. 10 11 Installation - Model E6002 These instructions are intended for the qualified technician installing the appliance in order to insure that the installation, adjustments and maintenance procedures are performed correctly and comply with the regulations currently in effect. Important: the hob must be disconnected from the power ...
Este manual também é adequado para os modelos :Hobs - E6002 (559.25 kb)