Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
Immediately remove such food using the glass scraper. Iridiscent discoloration can be caused by the bases of some pots. These do not interfere with the operation of the glass ceramic hob. Please refer to the enclosed brochure for further notes on cleaning. You can order our blade scraper (Order No. 087670) and the Gaggenau glass ceramic cleaner (Order No. 098690) from your Gaggenau dealer. The frame of the hob should be cleaned using a soft, damp cloth and light soapy liquid or a commercially available stainless steel cleaner. 7. Maintenance The appliance must always be disconnected from the mains when being repaired. If the appliance does not function correctly, check the household fuses first. If the power supply is functioning correctly, but your appliance still does not work, please contact your dealer or your local Gaggenau customer service agency. Specify the appliance type. The serial number and type of the appliance can be found on the quality control slip which is included with these instructions. Repairs may only be carried out by authorised electricians, in order to guarantee the safety of the appliance. Unauthorised tampering with the appliance will invalidate any warranty claims. 8. Remedying slight malfunctions yourself Not every malfunction can be ascribed to a defect of your cooker. If your appliance should not function properly, search for the fault in the list below. If you are not successful in remedying the fault with the aid of the list below, then contact your Gaggenau after-sales service. Fault Possible cause Remedy The appliance cannot be No electricity. Check the domestic fuse. switched on. Both right cooking zones The overheating protection has You can use the remaining cook with reduced power. been triggered. cooking zones. Both right cooking zones are operated on level 7, if level 8 or 9 is selected. After cooling down, the complete hob can be used normally. A cooking zone switches off The holiday safeguard is set to T urn the control knob to 0. after operating for a longer automatically switch off a cooking zone Now the cooking zone can period of time. The luminous 4 hours after the last operation. be switched on again as disc behind the corresponding normal. control knob flashes. After installation, the appliance The connecting cable between control Check the connecting cable. cannot be switched on. panel and hob is not plugged in correctly. Check the domestic fuse. 9. Installation Technical Data Total connected load: 8680 W Important notes on installation Pay attention to the “Important notes" on page 3 and 4. The appliance must only be connected by an authorised specialist, paying attention to the relevant regulations of the power supply companies and the regional construction regulations. The installation technician is responsible for the correct functioning of the appliance at the place of installation. He must instruct the user on how to disconnect the appliance from electricity in an emergency. If the range is not installed over a built-in cooker, protection against hazardous contact from below must be ensured after assembly, e.g. by installing an intermediate shelf that can only be detached using a tool. The distance between the intermediate shelf and the worktop in which the range is recessed must be at least 145 mm. There must be a gap of at least 20 mm at each side between the appliance and any flammable walls or furnishings. If all poles of the appliances cannot be isolated from the mains by removing an accessible plug, an isolating device with a contact gap of at least 3 mm must be installed (e.g. domestic fuse). No warranty claims can be lodged for any damage resulting from failure to observe these instructions. Subject to technical change without notice. Electrical connection The appliance must only be connected by an authorised specialist. All corresponding regulations must be observed. The mains connecting cable must at least correspond to type H 05 VV-F. Note for single phase connection: This device is intended for the connection to a power supply system with a maximum permissible system impedance Zmax of 0.46 Ohm at the interface point (power service box) of the user’s supply. The user has to ensure that this device is connected only to a power supply system which fulfills the requirement above. If necessary, the user can the ask the public power supply company for the system impedance at the interface point. Pay attention to the data on the rating plate. The appliance must be properly grounded. Connect the connecting cable to the mains. When connecting electrical appliances in the proximity of cooking surfaces, make sure that connecting cables do not come into contact with hot cooking surfaces. This appliance may be installed in kitchen combinations made of wood or similar combustible materials without taking additional measures. The built-in furniture and worktop where the appliance is installed must be heat resistant up to temperatures of 200° F/90° C. Prep...
Este manual também é adequado para os modelos :Hobs - CK483110/10 (908.95 kb)
Hobs - SP483110/01 (908.95 kb)