. Flammable cleaners such as lighter fluid or WD-40. Type of Soil Possible Solution Dry sugar, sugar syrup, milk or tomato spills. Melted plastic film or foil. All these items REQUIRE IMMEDIATE REMOVAL. Failure to remove these immediatly can permanently damage the surface. Remove these types of spills while the surface is hot using the razor blade scraper. Use a new, sharp razor in the scraper. Remove pan and turn off the element. Wearing an oven mitt, hold scraper at 30° angle, using care not to gouge or scratch the glass. Push soil off the heated area. After the surface has cooled, remove the residue and apply the glass ceramic cooktop cleaner. 9 WARNI NG RISK OF INJURY The blade is extremely sharp. Risk of cuts. Protect the blade when not in use. Replace the blade immediately when any imperfections are found. Follow manufacturer’s instructions. Burned-on food soil, dark streaks, and specks Soften by laying a damp paper towel or sponge on top of soil for 30 minutes. Use a plastic scrubber and glass ceramic cooktop cleaner or use the razor blade scraper. Rinse and dry. Greasy spatters Use a soapy sponge or cloth to remove grease; rinse thoroughly and dry. Apply glass ceramic cooktop cleaner. Metal marks: Iridescent stain Pans with aluminum, copper or stainless steel bases may leave marks. Treat immediately after surface has cooled with glass ceramic cooktop cleaner. If this does not remove the marks, try a mild abrasive ( Bon Ami® , Soft Scrub ® without bleach) with a damp paper towel. Rinse and reapply glass ceramic cooktop cleaner. Failure to remove metal marks before the next heating makes removal very difficult. Hard water spots: Hot cooking liquids dripped on surface Minerals in some water can be transferred onto the surface and cause stains. Use undiluted white vinegar, rinse and dry. Recondition with glass ceramic cooktop cleaner. Remove boilovers and stains before using the cooktop again. Surface scratches: Apply glass ceramic cooktop cleaner before using to remove sand-like grains and grit such as salt and sea- Small scratches are common and do not affect cooking. soning. Scratches can be reduced by using pans with They become smoother and less noticeable with daily use bases that are smooth, clean, and dry before use. Use of the glass ceramic cooktop cleaner. recommended glass ceramic cooktop cleaner daily. NOTICE: Diamond rings may scratch the surface. Maintenance This appliance requires no maintenance other than daily cleaning. For best results, apply cooktop cleaning cream daily. Service Troubleshooting 9 CAUTION If you encounter a problem, it often will merely be Repairs should only be done by a trained servicer. something minor. Before you call customer service, consider the suggestions and instructions below: Improper repair of your appliance may result in risk of severe physical injury or death. Fault Possible cause Measure Cooktop is not working The electric power supply has been Use other electrical appliances to check if there has interrupted. been a power outage. Check to see if there is a problem with the circuit breaker for the electrical installation. The appliance has not been cor- Make sure that the appliance has been connected rectly connected following the con- correctly. nection diagram. Electronic system malfunction. Contact the Technical Assistance Service. “ is flashing on the ele- The touch control zone is wet, very Clean the touch control zone, or remove the object. ment display dirty, food has boiled over, or an Lightly touch the corresponding touch key. The flash- object is lying on top of the touch ing should stop. control zone. “ flashes on all ele- The main switch has been activated Press the power key again. Reset the cooktop. ment displays. An continuously for more than 5 secaccoustic signal onds. sounds The cooktop turns off The main switch has been touched Press the main switch again. Reset the cooktop. by itself unintentionally. The display flashes ( no The pan is not ferromagnetic Check the bottom of the pan with a magnet. power) when you place The diameter of the pan is to small. Use a pan with an appropriate diameter for the ele a pan on an induction ment. element If the display still does not light up when you turn the element off and on again, disconnect the appliance at the circuit breaker. Wait 20 seconds and then reconnect it. The SpeedBoost func- The element is too hot. The SpeedBoost function operates the element with tion display flashes and the highest possible power. During long cooking then turnes off times, it is possible that the function will turn the ele ment off to protect the cooktop from overheating. You can continue to use the cooktop if the display is not flashing. Display “ and numbers A fault in the electronic system has Turn the appliance off and back on at the fuse or ciroccurred. cuit breaker. If the same fault occurs again, disconnect the appliance and call Technical Assistance Service. Display ” and numbers A fault has been detected....

Este manual também é adequado para os modelos :
Hobs - NIT5065UC/20 (3.09 mb)
Hobs - NIT5065UC/21 (3.09 mb)