Log:
Assessments - 5, GPA: 4.8 ( )

Instruções de Operação GE, Modelo CGESS

Fabricante : GE
Arquivo Tamanho: 311.93 kb
Arquivo Nome : cf1d1c46-ab71-1a24-e1f1-dd3186c446d1.pdf
Língua de Ensino: en
Ir para baixar



Facilidade de uso


Turn the switch to ON and unit will be ready to operate. The "|" indicates ON and "O" indicates OFF. 2. Flame ON/OFF Switch: This switch is located in the middle between the Main ON/OFF switch and the Heater ON/OFF switch on the control panel when looking at the back of the unit. Turn the switch to ON and the flame effect will turn on. The "|" indicates ON and the "O" indicates OFF. 3. Heater ON/OFF Switch: This switch is located to the left of the Flame ON/OFF switch on the control panel. It has a symbol of the sun directly below it. 4. Thermostat Control Dial: This dial is located at the furthest left corneron the control panel. It has a symbol of a thermostat directly below it. Turn the dial clockwise past the number 8. Youshouldhearasmallclickingsoundindicating the heater has started and heat will emit from the vents at the top of the unit from the front. To turn off heater, turn the dial counter clockwise past number 1 and turn the Heater SwitchtoOFFposition.Toincreasethedesired temperature, turn the dial clockwise towards Number 9. Main Power Flame Switch Switch Figure 3 - Electric Stove Control Panel Built-In Thermostat Heater Switch CLEANING AND MAINTENANCE WARNING: Always discon- nect power and allow the heater to cool before performing any cleaning,maintenanceorreloca- tion of this heater. Turn controls to OFF and remove plug from outlet or turn off circuit breaker to heater. Turn off heater and circuit breaker to heater before performing any cleaning and/or maintenance. Allow heater to cool completely. BULB REPLACEMENT WARNING: The halogen light bulbs in your unit can become extremely hot. Allow at least 10 minutes between turning off the heater and removing the light bulbs to avoid accidental burns. There are a total of 4 ( halogen light bulbs (type GX6.35 rated 120 volts, 35 watts) in your unit. • 1 bulbs provide illumination for the ember bed beneath the log set • 1 bulbs provide illumination for the flame generation assembly • 2 bulbs for replacement 117889-01B CLEANING AND 8. Secure the rear cover of the unit to the main frame by reattaching the 6 screws remove in MAINTENANCE step 1. Continued Most halogen light bulbs are rated to last approximately 1800 hours. Like all light bulbs, halogen bulbs require periodic replacement. When the bulbs in your unit have burned out you will notice or more of the following: • Flame is dim or dark in certain areas Screws • Log set ember bed appears dim or dark in Screws certain areas WARNING: Do not install replacement bulbs that exceed specified maximum watts. Figure 4 - Replacement Light Bulb Your unit must be opened in order to replace the light bulbs. To reduce the number of times you need to open the unit, replace all bulbs at the same time if they are close to the end of their rated life. Tools Required: Phillips Screw Driver Replacing Flame Generation Bulb 1. Unplug unit from the power supply. 2. Remove the six screws from the back of stove as shown in Figure 5. Remove back plate. 3. Locate the flame generation cylindrical drum (see Figure 6). It is constructed of two removable halves. They are two matte black sheet-metal pieces with holes in them, either of which can be removed from the unit. 4. Squeeze half of drum cylinder until its top edge clears the top drum track. Remove the bottom edge of the cylinder drum from the bottom drum track. This will give you access to the light bulbs. Note: Do not exert excessive pressure on t...

Este manual também é adequado para os modelos :
Hobs - CGESS (311.93 kb)
Hobs - CGESS (311.93 kb)
Hobs - CGESS (311.93 kb)
Hobs - CGESS (311.93 kb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias