Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
Ride safely! • Install the magnet, sensor, and bracket securely. Check these periodically. • If a child swallows a battery, consult a doctor immediately. • Do not leave the computer in direct sunlight for a long period of time. • Do not disassemble the computer. • Do not drop the computer to avoid malfunction or damage. • When you attempt to press MODE with the computer installed to the bracket, press around the marking section on the surface of the computer. Pressing other sections strongly may result in malfunction or damage. • Be sure to tighten the dial of the FlexTight bracket by hand. Tightening it strongly using a tool, etc. may damage the screw thread. • When cleaning the computer, bracket and sensor, do not use thinners, benzene, or alcohol. • A temperature sensor is built in the computer. If the sensor is heated by direct sunlight or body heat, it may not indicate the temperature correctly. • Dispose of used batteries according to local regulations. • LCD screen may be distorted when viewed through polarized sunglass lenses. Wireless Sensor The sensor was designed to receive signals within a maximum range of 70 cm, to reduce chance of interference. When adjusting the wireless sensor, note the following: • Signals cannot be received if the distance between the sensor and the computer is too large. • The receiving distance may be shortened due to low temperature and exhausted batteries. • Signals can be received only when the back of the computer is facing the sensor. Interference may occur, resulting in incorrect data, if the computer is: • Near a TV, PC, radio, motor, or in a car or train. • Close to a railroad crossing, railway tracks, TV stations and/or radar base. • Using with other wireless devices in close proximity. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:( 1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Modifi cations The FCC requires the user to be notifi ed that any changes or modifi cations made to this device that are not expressly approved by CatEye Co., Ltd. May void the user ’s authority to operate the equipment. Before using the computer, please thoroughly read this manual and keep it for future reference. How to install the unit on your bicycle 1Bracket band 2Bracket 3Nut 4Sensor 5Magnet 6Sensor rubber pad 7Bracket rubber pad 8Nylon ties (x2) 5 8 7 1 6 2 4 3 U.S. Pat. Nos. 5236759/5308419/6957926 Pat./Design Pat. Pending CCCOM1W-100224 066600950 2 Tire circumference reference table ETRTO Tire size L (mm) 47-203 12x1.75 935 54-203 12x1.95 940 40-254 14x1.50 1020 47-254 14x1.75 1055 40-305 16x1.50 1185 47-305 16x1.75 1195 54-305 16x2.00 1245 28-349 16x1-1/8 1290 37-349 16x1-3/8 1300 32-369 17x1-1/4 (369) 1340 40-355 18x1.50 1340 47-355 18x1.75 1350 32-406 20x1.25 1450 35-406 20x1.35 1460 40-406 20x1.50 1490 47-406 20x1.75 1515 50-406 20x1.95 1565 28-451 20x1-1/8 1545 37-451 20x1-3/8 1615 37-501 22x1-3/8 1770 40-501 22x1-1/2 1785 47-507 24x1.75 1890 50-507 24x2.00 1925 54-507 24x2.125 1965 25-520 24x1(520) 1753 24x3/4 Tubuler 1785 28-540 24x1-1/8 1795 32-540 24x1-1/4 1905 25-559 26x1(559) 1913 32-559 26x1.25 1950 37-559 26x1.40 2005 40-559 26x1.50 2010 47-559 26x1.75 2023 50-559 26x1.95 2050 54-559 26x2.10 2068 57-559 26x2.125 2070 58-559 26x2.35 2083 75-559 26x3.00 2170 28-590 26x1-1/8 1970 37-590 26x1-3/8 2068 37-584 26x1-1/2 2100 650C Tubuler 26x7/8 1920 20-571 650x20C 1938 23-571 650x23C 1944 25-571 650x25C 26x1(571) 1952 40-590 650x38A 2125 40-584 650x38B 2105 25-630 27x1(630) 2145 28-630 27x1-1/8 2155 32-630 27x1-1/4 2161 37-630 27x1-3/8 2169 18-622 700x18C 2070 19-622 700x19C 2080 20-622 700x20C 2086 23-622 700x23C 2096 25-622 700x25C 2105 28-622 700x28C 2136 30-622 700x30C 2146 32-622 700x32C 2155 700C Tubuler 2130 35-622 700x35C 2168 38-622 700x38C 2180 40-622 700x40C 2200 42-622 700x42C 2224 44-622 700x44C 2235 45-622 700x45C 2242 47-622 700x47C 2268 54-622 29x2.1 2288 60-622 29x2.3 2326 L mm When using the computer for the fi rst time or resetting to the factory default setting, format according to the following procedure. 1 Format (initialize) 1. Press and hold the MENU button. 2. Press the AC button. 3. Release the AC button. .. (Keep pressing the MENU button.) 4. Release the MENU button. 2 Select the speed and temperature unit When MODE is pressed and held, “Speed unit” and “Temperature unit” will appear for selection. Select “km/h” or “mph” for the speed unit, and “°C” or “°F” for the temperature unit. 3 Set the date When MODE is pressed and held, “Date format”, “Day”, “Month”, and “Year” will appear, in this order. Press MODE to change the value, and press MENU to register it. Set the values in the subsequent settings with in the same procedure. 4 Set the clock When MODE is pressed and held, “Display format”, “Hour”, and “Minute” will appear, in this order. * When 12h is selected, “AM/PM...