13. Always make sure tires are properly inflated (see page 2). WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking your Tricycle with Pneumatic Tires, check to make sure all parts listed on page 5 are included. If

The UV/IR protection level is up to Shade 16 (DIN) at all times. Models 94336 & 94337 (View from inside of helmet.) Battery Cover Low Battery Light Sensitivity Adjustment Adjusts the amount of light the lens requires to respond and darken with. Dark to Clear Delay Adjustment Adjusts the amount of time until the lens turns back to clear. These models include one built-in 3V CR2450 battery. Low Battery Light will illuminate when replacement is needed. Models 91212 & 91214 (View from inside of helm

Warning:The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Helmet Safety Warnings and Precautions Remove the protective film from both sides of the new cover lens. 1. Use this helmet for eye and face protection against harmful rays, sparks and sp

Write the invoice number on the inside of the front cover. Write the product’s serial number in the back of the manual near the assembly diagram, or write month and year of purchase if product has no number. Keep this manual and invoice in a safe and dry place for future reference. GENERAL SAFETY RULES 1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. 2. Keep bystanders, children, and visitors away while assembling and working with the Workstand. Distr

It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Save these instructions. Specifications Weight Capacity 350 lb. Unpacking When unpacking, make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. ASSEMBLY Read the entire Important Safety Information section at

Aside from the slight differences noted in this manual, the warnings, operation instructions, and maintenance procedures will remain the same. ® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at To prevent serious injury or blindness, Read and understand all warnings and Instructions before use. Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express writte

Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Before First Use 1. The Auto-Darkening Welding Helmet needs to be charged prior to use and after extended storage. Leave the solar panel on the helmet facing the sun for at least 4 hours

Note: If a selection of shades are recommended for your application, try the darkest setting first. Adjust headband so that the helmet is seated on the head as low as possible and close to your face. Adjust helmet’s angle when in the lowered position by turning the adjustable limitation washer. SHADE NUMBER SELECTION The shade number can be infinitely set manually between 9 - 13. Check with the Shade Guide Table on page 8 to determine the proper shade number for your application. To select a sha

Before First Use 1. The Auto-Darkening Welding Helmet needs to be charged prior to use and after extended storage. Leave the solar panel on the helmet facing the sun for at least 4 hours before first use. 2. Remove the protective film from both sides of the front lens (if not already done). 3. Follow the Before Each Use instructions below. Before Each Use 1. Check the Front Lens Cover to makes sure that it is clean, and that no dirt is covering the two sensors on the front of the Filter Cartridg