Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
When the service disconnecting means cannot be locked, securely fasten a prominent warning device such as a tag to the service panel. CAUTION: For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. WARNING — TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings. Always turn hood ON when cooking at high heat or when cooking flaming foods. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter. Use proper pan size. Always use cookware appropriate for the size of the surface element. WARNING — TO REDUCE THE RISK OF INJURYTO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING: SMOTHER FLAMES with a close- fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT. NEVER PICK UP A FLAMING PAN —You may be burned. DO NOT USE WATER, including wet dishcloths or towels — a violent steam explosion will result. Use an extinguisher ONLY if: You know you have a Class ABC extinguisher, and you already know how to operate it. The fire is small and contained in the area where it is started. The fire department is being called. You can fight the fire with your back to an exit. This fan suitable for use with solid- state speed controls. Operation The canopy hood is designed to remove smoke, cooking vapors and odors from the cooktop area. For best results, start the hood before cooking and allow it to operate several minutes after the cooking is complete to clear all smoke and odors from the kitchen. control panel location Opening the canopy hood control panel: The hood controls are located in a grey panel on the underside of the canopy. To open the panel, press on the front edge of panel and release. The control panel will drop down. light switch blower switch blower speed switch Operating the light: ON: Move the light switch to the “1” position. OFF: Move the light switch to the “0” position. Operating the blower: ON: Move the blower switch to the “1” position. OFF: Move the blower switch to the “0” position. Adjusting the blower speed: The blower has variable speed control. Move the switch to the far left for LOW speed and to the far right for HIGH speed. Closing the range hood controlpanel: Push up on the front edge of the control panel. The control panel will slide up into the canopy. Cleaning Filters: The filters should be washed frequently. Place metal filters in dishwasher or hot detergent solution to clean. Exterior surfaces: Clean the range hood with a mild detergent and soft cloth. Do Not use abrasive cleanser or steel wool pads. support flange support flange Wiring diagram Accessories available from your dealer Note: Instructions are included with each kit. Backsplash*: Must be installed before hood is installed. Stainless steel only. Part No. 8171295 30" (76.2 cm) Part No. 4378615 36" (91.4 cm) Part No. 8171296 48" (121.9 cm) Utensil Bar: Stainless steel only Part No. 4378619 (side) 15" (38 cm) long Part No. 8171299 (back) 30" (76 cm) long Part No. 4378618 (back) 35-3/8" (90 cm) long Charcoal Filters: Part No. 4378623 (2 per pkg.) Non-Vented (Recirculating) Kits*: Part No. 4378621 (stainless steel) Part No. 4378622 (white) Part No. 8171290 (biscuit) Wire Rack: Chrome only Part No. 8171297 30" (76.2 cm) Part No. 4378616 36" (91.4 cm) Part No. 8171298 48" (121.9 cm) Rack Hanger Kit: Chrome only Part No. 4378617 Chimney Extensions*: Part No. 8171313 (stainless steel) Part No. 8171315 (biscuit) Part No. 8171314 (white) *These instructions must be read before starting the canopy hood installation. Maintenance Replacing the light bulb: This range hood uses fluorescent lamp type F33-15W-T8 and starter type 52. Remove the retainer clips from both ends of the light cover. Carefully slide the cover all the way to the right. Then lower the left end of the glass below the support flange and remove the glass by sliding it back from the left. Install a new fluorescent light bulb. Position the right end of the light cover over the flange and slide the cover all the way to the right. Position the left end of the light cover over the flange and slide the cover back to left. Reinstall the retainer clips. retainer clips For assistance: If you have questions about operating, cleaning or maintaining your range hood: . Call the KitchenAid Consumer Assistance Center, 1-(800) 422-1230. If you need service: Maintain the quality built into your appliance by calling a KitchenAidauthorized service company.To obtain the name and number of an authorized service company: . Contact the dealer from whom you purchased the appliance; . Look in theYellow Pages of your telephone directory under “Appliances — Household — Major — Service and Repair;” . Call the KitchenAid Consume...