Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
Touch control unlit Lights off When pressed for 2 seconds it switches the electroluminescent lighting on and off. This function is independent from the basic functions of the control unit. It is therefore possible to switch on simultaneously the hood lighting and the electroluminescent lighting. During the electroluminescent lighting mode the touch control is unlit. Touch control unlit Lights off Touch control lit Lights on Touch control unlit Electroluminescent lighting on T1 When pressed the motor is stopped, regardless of the speed it is set to. Touch control lit Motor on Touch control unlit Motor off T2 When pressed the motor is set to the first speed Touch control lit T3 By a brief pressing the motor is set to the second speed. Touch control lit Second speed on By pressing the touch control for approximately 2 seconds the Delay function is enabled, i.e delayed shutdown of the appliance ensuring a complete elimination of the residual odours. This function can be activated at OFF-position and at 1°, 2° and 3°speeds. It can be stopped in advance by pressing any of the touch controls (T) with the exception of T3. The Delay function works according to the following scheme: 1°speed / OFF = 20 minuets 2°speed = 15 minutes 3°speed = 5 minutes Flashing touch control Delay function on T4 When pressed the motor is set to the third speed Touch control lit T5 When pressed the motor is set to the boost option timed to 5 minutes. At the end of 5 minutes of boost option the hood starts again at the speed it was set to previously. If the hood is in the OFF-position and the boost option is selected, after 5 minutes the speed is reduced to setting 1 (T2). Touch control lit F When pressed for 4 seconds it resets the filter alarm signal indicated by flashing of the touch control T1. This procedure can be carried out only when the motor is stopped. Touch control lit Metal grease filters saturation alarm. Metal grease filters need to be washed. The alarm starts up after 100 working hours. Flashing touch control Charcoal odour filter saturation alarm. Charcoal filter has to be replaced and metal grease filters washed. The alarm starts up after 200 working hours. (Activation; check the paragraph “Charcoal filter”) Maintenance and Cleaning Before carrying out any maintenance or leaning isolate the cooker hood from the mains supply. The cooker hood must be kept clean, as a build up of grease or fat can be a fire hazard. External cleaning Wipe the cooker hood frequently with warm soapy water using a mild detergent. Never use scouring pads or abrasive cleaners. Never use excessive amounts of water when cleaning particularly around the control panel. Cleaning the Comfort Panels • Pull the Comfort Panel to open it. • Disconnect the panel from the hood canopy by sliding the fixing pin lever. • The comfort panel must never be washed in a dishwasher. • Clean the outside using a damp cloth and neutral liquid detergent. • Clean the inside as well using a damp cloth and neutral detergent; do not use wet cloths or sponges, or jets of water; do not use abrasive substances. • When the above operation has been completed, hook the panel back to the hood canopy and close it by turning the knob in the opposite direction. Metal Grease Filters The grease filters absorb grease and dust during cooking to help keep the cooker hood clean inside, and should be cleaned when the F - touch control lights up or at least every 2 months of operation, or more frequently for particularly heavy usage. Cleaning the filters • Pull the Comfort Panel to open it. • Remove the filters one by one pushing them towards the back side of the unit and simultaneously pulling downwards. • The metal grease filters can be washed, by hand, in mild soapy water or in a dishwasher. Allow to dry completely before refitting. Any kind of bending of the filters must be avoided when washing them. • When fitting the filters into the hood pay attention that they are mounted in correct position and that the handle faces outwards. • Close the comfort panel. Alarm signal reset • Stop the motor. • Press the F -touch control for at least 4 seconds until the T1 -touch control flashes. Before carrying out any maintenance or ...
Este manual também é adequado para os modelos :Fans - JLBIHD906 (592.86 kb)
Fans - JLBIHD906 (592.86 kb)
Fans - JLBIHD906 (592.86 kb)
Fans - JLBIHD906 (592.86 kb)