Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
CAUTIONBulb may be hot. CAUTION Use of bulbs greater than 20 watts will cause the fuse to open. CAUTIONUse of a fuse greater than 4 amps may damage the transformer. ELECTRICAL BOXFUSEFigure 2Figure 3Operation WARNINGAlways switch off the electrical supply before carrying out any operation on the appliance. CAUTIONBulb may be hot. CAUTION Use of bulbs greater than 20 watts will cause the fuse to open. CAUTIONUse of a fuse greater than 4 amps may damage the transformer. ELECTRICAL BOXFUSEFigure 2Figure 3 Halogen Bulbs This range hood requires two halogen bulbs (Type JC, 12Volt, 20Watt Max, G-4 Base). To change bulbs: 1 Open the cover by prying from the proper slots. 2 Remove the bulb by pulling sideways. (DO NOT ROTATE). 3 Replace with Type JC, 12Volt, 20 Watt Max, G-4 Base halogen bulb. Do not touch replacement bulb with bare hands! Fuse Placement IF LIGHTS FAILTO OPERATE, DISCONNECT POWERAT THE SERVICE ENTRANCE. CHECK THE FUSE AND REPLACE IF NECESSARY. 1 Raise or remove the lower decorative flue. See Figure 3. 2 Remove the cover from the electrical box. 3 Unscrew the cap from the fuse holder and remove the fuse. 4 Replace the fuse with the same size and amperage (5 x 20mm, 4 amp, 125 volt). 5 Reinstall the fuse holder cap, electrical box cover and flue. 6 Reconnect power at the service entrance. Care and Cleaning 111 CARING FOR YOUR RANGE HOOD Proper maintenance of the Range Hood will assure proper performance of the unit. Grease Filters The grease filters should be cleaned frequently. Use a warm detergent solution. Grease filters are dishwasher safe. See “INSTALL FILTERS” section for removal and installation instructions. Non-Ducted Recirculation Filter The non-ducted recirculation filter should be changed every 6 months. See “INSTALL FILTERS” section for removal and installation instructions. Hood Cleaning Stainless steel is one of the easiest materials to keep clean. Occasional care will help preserve its fine appearance. Cleaning tips: · Hot water with soap or detergent is all that is usually needed. · Follow all cleaning by rinsing with clear water. Wipe dry with a clean, soft cloth to avoid water marks. · For discolorations or deposits that persist, use a non-scratching household cleanser or stainless steel polishing powder with a little water and a soft cloth. · For stubborn cases, use a plastic scouring pad or soft bristle brush together with cleanser and water. Rub lightly in direction of polishing lines or “grain” of the stainless finish. Avoid using too much pressure which may mar the surface. · DO NOT allow deposits to remain for long periods of time. · DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface causing rust. · DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact with stainless steel for extended periods. Many of these compounds contain chemicals which may be harmful. Rinse with water after exposure and wipe dry with a clean cloth. Painted surfaces should be cleaned with warm water and mild detergent only. 12 Installation CHECK CONTENTS Unpack hood and check contents. You should receive: 1 - Hood 1 - Decorative Flue Assembly 1 - Parts Bag (B080810604) containing: 1 - Mounting Bracket 1 - Discharge Collar 1 - Flue Mounting Bracket 6 - Mounting Screws (4,8 x 38mm Pan Head) 7 - Mounting Screws (3,9 x 9,5mm Pan Head) 2 - Mounting Screws (3.9 x 6mm Flat Head) 6 - Drywall Anchors 1 - Installation Instructions 1 - Warranty Card DISCHARGE COLLAR 2 MOUNTING BRACKET SCREWS (3.9 x 6mm Flat Head) 6 DRYWALL MOUNTING ANCHORS BRACKET 7 MOUNTING SCREWS (3.9 x 9.5mm Pan Head) FLUE MOUNTING BRACKET DECORATIVE FLUE 6 MOUNTING SCREWS (4.8 x 38mm Pan Head) Figure 4 13InstallationCAUTIONTo reduce the risk of fire, use only metal ductwork. ROOF CAPROUND DUCTDECORATIVE FLUEHOODWALL CAPROUND ELBOW6” ADAPTER24”TO 30”ABOVE COOKING SURFACE(See “Install mounting bracket”section,for mounting restrictions) 9” 4-1/2” 18”- 22” WARNINGElectrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards. This range hood must be properly grounded. Turn off electrical power at service entrance before wiring. Figure 5Figure 613InstallationCAUTIONTo reduce the risk of fire, use only metal ductwork. ROOF CAPROUND DUCTDECORATIVE FLUEHOODWALL CAPROUND ELBOW6” ADAPTER24”TO 30”ABOVE COOKING SURFACE(See “Install mounting bracket”section,for mounting restrictions) 9” 4-1/2” 18”- 22” WARNINGElectrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards. This range hood must be properly grounded. Turn off electrical power at service entrance before wiring. Figure 5Figure 6 INSTALL THE DUCTWORK 1 Decide where the ductwork will run between the hood and the outside. 2 A straight, short duct run will allow the hood to perform most efficiently. 3 Long duct runs, elbows, and transitions will reduce the performance of the hood. Use as few of them as possible. Larger du...