Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
1This range hood is designed to discharge upward. For vertical discharge, run duct work between the hood location and roof cap location. To get the best result, use a minimum number of transitions and elbows. Be sure to attach a roof cap to avoid leaking rain in the end. 2The range hood unit must be mounted to a liner which has the following dimensions. Install the liner securely after checking that the opening size of the liner is the same as the figure below. INSTALLATIONCAUTIONThe liner should be installed tightly. If the liner installation is not correct, the range hood unit may become detached and fall. 1.PREPARATIONWARNING• If the range hood is not installed properly, it could become detached and fall. • Ensure that the metal duct does not touch other metal housing materials, otherwise fire or electric shock could result. 1This range hood is designed to discharge upward. For vertical discharge, run duct work between the hood location and roof cap location. To get the best result, use a minimum number of transitions and elbows. Be sure to attach a roof cap to avoid leaking rain in the end. 2The range hood unit must be mounted to a liner which has the following dimensions. Install the liner securely after checking that the opening size of the liner is the same as the figure below. INSTALLATIONCAUTIONThe liner should be installed tightly. If the liner installation is not correct, the range hood unit may become detached and fall. INSTALLATION (continued) 3Run house wiring between service panel and hood location. 4Prepare the range hood unit. (1) The range hood is supplied with the exhaust pipe fixed on its top plate. (2) Provide a transition duct (not supplied) to connect the exhaust pipe and external duct. The diameter of the transition duct should be more than 6". (3) Be sure to keep 1-3/16" overlapping length of the exhaust pipe and transition duct. INSTALLATION (continued) 3Run house wiring between service panel and hood location. 4Prepare the range hood unit. (1) The range hood is supplied with the exhaust pipe fixed on its top plate. (2) Provide a transition duct (not supplied) to connect the exhaust pipe and external duct. The diameter of the transition duct should be more than 6". (3) Be sure to keep 1-3/16" overlapping length of the exhaust pipe and transition duct. 2. RANGE HOOD MOUNTING 1Hold up the range hood unit and insert it into the opening of the liner. When the 4 securing plates on both sides have passed through the top of the liner, turn them outward to secure the range hood on the liner temporarily. Make sure that the top of the exhaust pipe is inserted into the bottom of the transition duct. INSTALLATION (continued) 2. RANGE HOOD MOUNTING 1Hold up the range hood unit and insert it into the opening of the liner. When the 4 securing plates on both sides have passed through the top of the liner, turn them outward to secure the range hood on the liner temporarily. Make sure that the top of the exhaust pipe is inserted into the bottom of the transition duct. INSTALLATION (continued) INSTALLATION (continued) 2Remove 4 screws which are fixed to the front cover. The front cover swings open 90° as shown in Fig. CA UTION Do not detach the front cover from the range hood unit. The hinge may be damaged. 3Align 4 screw holes of the liner and range hood unit, then fix securely using the supplied screws and nuts. NOTE Fasten all screws and nuts evenly. 4Make the duct joint secure and air tight using non-flammable tape such as duct tape, etc. (not supplied) NOTE Make sure that the shutter installed in the exhaust pipe moves freely. INSTALLATION (continued) 2Remove 4 screws which are fixed to the front cover. The front cover swings open 90° as shown in Fig. CA UTION Do not detach the front cover from the range hood unit. The hinge may be damaged. 3Align 4 screw holes of the liner and range hood unit, then fix securely using the supplied screws and nuts. NOTE Fasten all screws and nuts evenly. 4Make the duct joint secure and air tight using non-flammable tape such as duct tape, etc. (not supplied) NOTE Make sure that the shutter installed in the exhaust pipe moves freely. INSTALLATION (continued) 3. CONNECTING POWER SUPPLY WIRES WARNING • Electrical wiring should be done by a qualified person(s) in accordance with all- applicable codes and standards, including fire-rated construction. An unqualified person doing the work could result in fire, electric shock or injury. • This range hood uses 120V AC. Do not connect to other voltage since fire, electric shock or damage could result. 1Remove the nut from the conduit connector at the end of power wiring. WARNING Be sure to switch power OFF at service panel before wiring. 2Remove one screw fixing the wire cover and detach it. 3Connect the conduit through the connecting hole of the body using the nut previously removed. INSTALLATION (continued) 4Connect the electrical wires as follows: Connect wires tightly and securely using wire connectors (not supplied). ...
Este manual também é adequado para os modelos :Fans - BUF-02 (484.01 kb)