Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
The outlet box must be securely anchored and capable of withstanding a load of at least 50 lbs. 15. Securely attach the hanger bracket to the outlet box using the two screws supplied with the outlet box (Figure 11). WARNING ! WARNING ! To reduce the risk of fire, electric shock, or personal injury, mount fan to outlet box marked acceptable for fan support, and use screws supplied with outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician in in doubt. Hanger bracket must seat firmly against outlet box. If the outlet box is recessed, remove wall board until bracket contacts box. If bracket and/or outlet box are not securely attached, the fan could wobble or fall. 6 WARNING ! The fan must be hung with at least 7' of clearance from floor to blades (Figure 22). CEILING AT LEAST 7' FLOOR Figure 22 WARNING ! The outlet box must be securely anchored and capable of withstanding a load of at least 50 lbs. 17. Securely attach the hanger bracket to the outlet box using the two screws supplied with the outlet box (Figure 23). To reduce the risk of fire, electric shock, or personal injury, mount fan to outlet box marked acceptable for fan support, and use screws supplied with outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician in in doubt. WARNING ! WARNING ! Hanger bracket must seat firmly against outlet box. If the outlet box is recessed, remove wall board until bracket contacts box. If bracket and/or outlet box are not securely attached, the fan could wobble or fall. TAB OUTLET BOX TWO SCREWS SUPPLIED WITH OUTLET BOX HANGER BRACKET Figure 23 18. Carefully lift the fan and seat the hanger ball/downrod assembly on the hanger bracket that was just attached to the outlet box (Figure 24). Be sure the groove in the ball is lined up with tab on the hanger bracket (Figure 23). Failure to seat tab in groove could cause damage to electrical wires and possible shock or fire hazard. WARNING ! NOTE: CEILING COVER, SUPPLY WIRES AND OUTLET FAN WIRES OMITTED BOX FOR CLARITY. HANGER BRACKET Figure 24 DOWNROD ASSEMBLY HANGER BALL/ WARNING ! To avoid possible fire or shock, do not pinch wires between the hanger ball/downrod assembly and hanger bracket. WARNING ! To avoid possible fire or shock, be sure that electricity is turned off at the main fuse box before wiring. NOTE: If you are not sure if the outlet box is grounded, contact a licensed electrician for advice, as it must be grounded for safe operation. NOTE: If you are installing a SR120 Remote Control or a SW140 Wall Control to operate the fan and light, refer to the installation instructions and wiring diagrams shown in Section A of this Owner’s Manual. 19. For a wall control installation you will need a three-wire (with ground) conductor cable between the ceiling and wall outlet boxes. This will allow you to control the fan separately from the lights. Figure 25 is a basic wiring diagram that will control the uplight and downlight on a switch and the fan on a separate control. Refer to the installation instructions and wiring diagrams supplied with the Emerson Fan Control Owner’s Manual. a. Connect the green grounding lead from the hanger ball and the green grounding lead from the hanger bracket to the grounding conductor of supply (this may be a bare wire or a wire with green colored insulation). Securely connect wires with wire connector supplied. b. Securely connect the white wire from the downrod to the supply white (neutral) wire using wire connector supplied. Securely connect the black wire from the downrod to the supply black (hot) wire using wire connector supplied. c. Cut terminal off of the yellow lead wire and strip insulation 1/2” from end of wire. d. Securely connect the blue wire and yellow wire from the downrod to the supply red (hot) wire using wire connector (supplied). After connections have been made, turn leads upward and carefully push leads into the outlet box, with the white and green leads on one side of the outlet box and the black, blue and yellow leads on the other side of the outlet box. 20. To complete the ceiling fan assembly, proceed to the “FINAL ASSEMBLY” section. 10 Maintenance IMPORTANT CARE INSTRUCTIONS for your Ceiling Fan Periodic cleaning of your new ceiling fan is the only maintenance that is needed. When cleaning, use only a soft brush or lint free cloth Do not use water when cleaning your ceiling fan. It to avoid scratching the finish. could damage the motor or the blades and create the WARNING ! possibility of an electrical shock. Abrasive cleaning agents are not required and should be avoided to prevent damage to finish. ! WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORE TROUBLE SHOOTING YOUR FAN. Trouble Shooting TROUBLE PROBABLE CAUSE SUGGESTED REMEDY 1. Fan will not star...
Este manual também é adequado para os modelos :Fans - CF2300OB01 (312.04 kb)
Fans - CF2300TG01 (312.04 kb)
Fans - CF2300S01 (312.04 kb)