Assessments - 4, GPA: 3.5
(
)
)
|
Facilidade de uso
This time can be lengthened or shortened to 20, 30, 40 or 50 hours. – A time of 20 hours should be programmed in kitchens with frequent pan or deep frying. – A time of 20 hours should also be programmed if the kitchen is only used occasionally. Otherwise grease which has accumulated over a long period of time will harden on the filters making cleaning more difficult. ^ Press the On/Off button to turn off the fan. ^ Press the Delayed Shut Down and grease filter buttons at the same time. The indicator for the grease filter and one of the _indicators will flash. The lit _indicator shows the programmed time: 1st indicator from the left = 20 hours 2nd indicator from the left = 30 hours 3rd indicator from the left = 40 hours 4th indicator from the left = 50 hours. ^ Use the $or &button to select the desired time. ^ Store the selection by pressing the grease filter button. If the procedure is not stored within 4 minutes of programming, the hood will automatically default to the "old" data. Cleaning and care Before cleaning or servicing the hood, disconnect it from the power supply by either removing the fuse, unplugging it from the outlet or manually "tripping" the circuit breaker. Cleaning the casing ,Never use abrasive cleaners, scouring pads, steel wool or caustic (oven) cleaners on the hood. They will damage the surface. ^ All external surfaces and controls can be cleaned with warm water and liquid dish soap applied with a soft sponge. ^ Wipe dry using a soft cloth. Do not use too much water when cleaning the controls. Water could penetrate into the electronics and cause damage. ^ Glass surfaces can be cleaned using glass cleaner. Avoid: – cleaning agents containing soda, acids or chlorides, – abrasive cleaning agents e.g. powder or cream cleansers, – abrasive sponges, e.g. pot scourers or sponges which have been previously used with abrasive cleaning agents. These will damage the surface. Stainless steel Stainless steel surfaces can be cleaned using a non-abrasive stainless steel cleaner. To help prevent resoiling, a conditioner for stainless steel can also be used. Apply sparingly with even pressure. Stainless steel colored controls These controls may become discolored or damaged if not cleaned regularly. Do not use a stainless steel cleaner on these controls. Cleaning and care Grease filters The reusable metal grease filters remove solid particles from the vented kitchen air (grease, dust, etc). ^ Clean the filters -by hand: use a scrub brush in warm water with a mild detergent. -in a dishwasher: place the filters in the lower basket, making sure that the spray arm is not blocked. The grease filters should be cleaned every 3-4 weeks or whenever the grease filter timer indicator lights. A dirty filter is a fire hazard. Depending on the detergent, cleaning the grease filters in a dishwasher may cause permanent discoloration of the filter surface. Performance of the filter will not be affected by this discoloration. ^ After cleaning, the filters can be placed on a towel to air dry. ^ While the filters are removed, clean any dirt or grease from the filter casing to prevent the risk of fire. When putting the grease filters back make sure that the locking clips are visible facing down towards the cooking surface. If the filters are incorrectly installed, insert a small screwdriver into the slit along its edge to disengage it from the ^ To remove the grease filters press the locking clips in towards the middle of the filter. Holding carefully, lower and remove the filter. casing. ^ After returning the grease filters, press the grease filter button for 3 seconds to reset the timer. The indicator light will go out. ^ If the grease filters are cleaned before the timer has reached its maximum, the grease filter button should be pressed for 6 seconds to reset the counter to zero. Cleaning and care Changing the light bulb To change a bulb: Before changing the light bulbs, disconnect the hood from the power supply by either removing the fuse, unplugging it, or manually "tripping" the circuit breaker. When in use halogen bulbs become extremely hot, and they can burn your hands. Do not attempt to change the bulbs until they have had sufficient time to cool down. Do not touch the bulb surface. Fingerprints or body oils deposited on the bulb will decrease the life of the bulb. Please follow the bulb manufacturer’s instructions. ^ Remove the outer ring, a. ^ Support the glass, c, while detaching the circlip, b. Be careful not to let the glass fall out. ^ Pull the old bulb, d, out of its socket and replace it with a new one. ^ Reinstall the glass, circlip and outer ring. Never use the lights without the glass, c, installed. The glass is specially made to filter harmful light rays. After Sales Service In the event of a fault which you cannot correct yourself please contact: – Your Miele Dealer or – The Miele Technical Service Department USA 1-800-999-1360 techserv@mieleusa.com CDN 1-800-565-6435 service@miele.ca When contacting...