Log:
Assessments - , GPA: ( )

Instruções de Operação Electrolux, Modelo PLHV36W7CC

Fabricante : Electrolux
Arquivo Tamanho: 1.15 mb
Arquivo Nome : PLHV36W7CC_use-care.pdf

Língua de Ensino: en

O documento está colocado, por favor, espere
O documento está colocado, por favor, espere

Facilidade de uso


The damper should be on the cold air side of the thermal break. The break should be as close as possible to where the ducting enters the heated portion of the house. 5. Hood installation height above cooktop is the users preference. The lower the hood above the cooktop, the more efficient the capturing of cooking odors, grease and smoke. We recommend the hood be installed 30-36" above the countertop. The lower height may be inconvenient for tall people and large cooking vessels. Check your ceiling height and the hood height maximum before you select your hood. 4 Installation Preparation of mounting surface (Drywall) Tools required for installation Screw driver (flat head, pozidrive n°2 and torx 10) Allen key 4mm Electric drill with twist bit 0 10 mm Fastener Locations Figure 2 1. Select a mounting height comfortable for the user and mark on wall behind cooktop. 2. Mark center line of cooktop and draw vertical line from bottom of hood to the ceiling. 3. Tape template, matching center-line and hood bottom as shown in Fig. 2. Distance from bottom of template to the ceiling must be minimum 29 15/16“. 4. Mark centers of the 6 fastener locations through template on wall then remove template. 5. Mark wall with horizontal line 1" above highest and 1" below lowest fastener location. 6. Find studs behind drywall by tapping wall or using a stud finder. Mark the center of the studs with a vertical line to the right and left of the marked fastener location. Note: Each 2 x 6 must span at least 2 studs side to side. 7. Cutout drywall along marked lines. Install each 2 x 6 between studs firmly flush with stud front. Make sure all mounting screws will anchor to added lumber. Replace drywall and refinish. 8. Remark center line and hood bottom on same location as before and tape template on wall as in step 3 above. 9. Mount 2 mounting hooks with wood screws (supplied in mounting hardware kit) on locations marked on template, then remove template. 10. Install duct cover ceiling bracket to wall flush to ceiling with drywall anchors supplied. S Installation Appliance Installation: 1. Hang hood on 2 mounting hooks through the rectangular cutouts on back of hood. 2. Level the appliance, using a carpenters level across bottom of hood with leveling screws in rectangular cutouts. 3. Secure hood with 2 screws on bottom and 2 on top. Figure 3 Screws Figure 4 4. Connect ducting (Figure 4): Note: for blower serviceability, leave a gap of 1" minimum between top of transition and sheet metal duct and cover gap with a starting collar wrapped around duct and transition. Locate collar screws so they fit into corner of duct cover. Secure collar to transition and duct with three sheet metal screws each. Seal with duct tape. Be sure to locate screws below damper lines drawn on transition. Mark onto exterior of transition the ,V‘ location of the damper within. Secure ducting to transition with three sheet metal screws each. Be sure to locate screws below damper lines drawn on transition. Seal with duct tape. Note: Do not...

Este manual também é adequado para os modelos :
Fans - PLHV36W7CC (1.15 mb)
Fans - PLHV36W7CC (1.15 mb)
Fans - PLHV36W7CC (1.15 mb)
Fans - PLHV36W7CC (1.15 mb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias