Do not install a damaged or incomplete appliance. Hood assembly with filter(s) Chimney assembly (2 piece) Mounting bracket Blower exhaust cowling (2 blower units only) Framework assembly (2 piece) Mounting and assembly hardware Use and care manual Make sure you have everything necessary for proper installation before proceeding. A B C D E F G A B C D E F G preparing for insTallaTion preparing for insTallaTion WARNING • • • • The electrical service to the range hood should be installed only by a

102138 Rev. C To Our Valued Customer: Congratulations on your purchase of the very latest in Dacor ® products! Our unique combination of features, style and performance make us The Life of the Kitchen ™, and a great addition to your home. In order to familiarize yourself with the controls, functions, and full potential of your new Distinctive Appliance, we suggest that you thoroughly read this use and care manual, beginning with the Important Safety Instructions section. All Dacor appliances are

Two staggered 45° angles are better than one 90°. • Keep turns as far away from the hood exhaust as possible, with as much space between each bend as possible. • For best performance, use round duct instead of rectangular, especially when elbows are required. • If multiple elbows are used, try to keep a minimum of 24” (61 cm) of straight duct between them. • Avoid “S” or “back to back” configurations of adjacent elbows. • In regions where the weather gets extremely cold, thermal breaks, such as

Use of a soft cloth reduces the risk of scratching. If the cloth is wet ensure that a dry soft cloth is used to wipe down the surface again reducing the risk of any surface rust appearing. Glass Surface The inlay glass panel can be cleaned using warm soapy water. Ensure the cloth is well wrung before cleaning. Use a dry soft cloth to remove any excess moisture left after cleaning. Cleaning grease filters The mesh filters can be cleaned either by hand or in the dishwasher. After cleaning ensu

• Similarly, position the lower chimney section and fix the lower part to the frame using the 2 screws 12c (2,9 x 9,5) provided. • When installed in the recirculation mode the ducting outlet extension pieces 14.1 should align with the rectangular holes in each side of the chimney. • Position the recirculation grilles 8a and 8b so the slats face in a forwards and upwards direction. Fitting the Hood Body • Before fixing the hood body to the frame: • Pull the Comfort Panel to open it. • Disconnect

The appliance is not fixed properly on the brackets. Take down the appliance and check it is properly fixed. The fan blade is damaged. Switch off the appliance. Repair to be carried out by qualified service personnel only. The fan motor is not fixed tightly. Light on, but fan does not work. The fan blade is jammed. The motor is damaged. Both light and fan do not work. Light bulb broken. Replace with a bulb with correct rating. Problem with electrical connection Check the electrical connection wi

Technical Details Models Dimensions (in cm) Height Width Depth Maximum absorbed power Motor power Lighting Length of the cable Electrical connection 8160 D 80-135 59,8 47 170 W 1 x 155 W 1 x 11 W (PL) 150 cm 220-240 V 8190 D 82-137 89,8 48 170 W 1 x 155 W 1 x 11 W 150 cm 220-240 V 8260 D 80-135 59,8 47 200 W 1 x 155 W 2 x 20 W (G4) 150 cm 220-240 V 8290 D 82-137 89,8 48 200 W 1 x 155 W 2 x 20 W (G4) 150 cm 220-240 V 8360 D 80-135 59,8 47 175 W 1 x 130 W 2 x 20 W (G4) 150 cm 220-240 V 8390 D 82-1

• When the hood is used in its extractor function, the following rules must be followed to obtain optimal operation: — short and straight outlet hose — keep bends in outlet hose to a minimum — never install the hoses with an acute angle, they must always follow a gentle curve only — keep the hose as large as possible (preferably the same diameter as the outlet hole). • Failure to observe these basic rules will drastically reduce the performance and increase the noise levels of the extractor hood