Assessments - 2, GPA: 3 ( )

Fabricante : Sony Arquivo Tamanho: 1.21 mb Arquivo Nome : Língua de Ensino:

por este dispositivo também tem outras instruções :

VCR jogadores / vídeo - SLV-SE810E (996.12 kb)

VCR jogadores / vídeo - SLV-SE810E (1.28 mb)

VCR jogadores / vídeo - SLV-SE810E (1.29 mb)

VCR jogadores / vídeo - SLV-SE810E (1.23 mb)

The monaural sound previously recorded is replaced while the original hi-fi sound remains unchanged. Use this feature to add commentary to a tape that you have recorded with a camcorder. t LINE-2 L o R X Before you start... • Open the t LINE-2 L o R jacks cover on the front panel and connect a playback source. • Turn on the TV and set it to the video channel. 1 Insert a source tape into your stereo system (or the playback VCR). Search for the point to start playback and set it to playback pause. 2 Insert a prerecorded tape with its safety tab in place into this (recording) VCR. Search for the start of the section to be replaced and press X (pause). TheVCR enters pausemode. 3 Press AUDIO DUB. The programme position changes to “L2,” and the indicator appears in the display window. 4 To start editing, press the X (pause) buttons on this VCR and the stereo system (or other VCR) at the same time. After you use this feature, the audio in playback mode is automatically set to monaural. To stop editing Press x (stop) on this VCR and the stereo system (or other VCR). To listen to both the hi-fi and normal audio Set AUDIO MIX to ON in the OPTIONS-1 menu (page 81). Use this feature to listen to dubbed audio over the original hi-fi audio. When AUDIO MIX is set to ON, the AUDIO MONITOR button does not function. Remember to reset AUDIO MIX to OFF after playing the tape. Note • If you eject the tape or turn the VCR off, AUDIO MIX is automatically set to OFF. Editing Audio dubbing (SLV-SE810D/E and SX810D only) Additional Information Troubleshooting If you have any questions or problems not covered below, please consult your nearest Sony service facility. Symptom Remedy Power The ?/1 (on/standby) switch does not function. • Connect the mains lead to the mains securely. The power is turned on but the VCR does not operate. • Moisture condensation has occurred. Turn the power off, unplug the mains lead and leave the VCR to dry for over three hours. The VCR is plugged in but the display window remains dark. • Set POWER SAVE in the OPTIONS-2 menu to OFF (see page 82). ClockThe clock has stopped and “–:––” appears in the display window. • The clock stops if the VCR is disconnected from the mains for more than one hour. Reset the clock (and timer). Playback The playback picture does not appear on the TV screen. • Make sure the TV is set to the video channel. If you are using a monitor, set it to video input. • If the VCR is connected to the TV with the Scart cable, make sure the VIDEO indicator is lit in the display window. Use the t TV/VIDEO button on the remote commander to light up the VIDEO indicator. The picture is not clear. • If your TV is connected to the VCR with both Scart and aerial cables, make sure the RF channel is set to OFF (see page 21). • Existing broadcasts may interfere with the VCR. Reset the RF channel output of your VCR. • Adjust the tracking with the PROGRAM +/– buttons on the VCR. • The video heads are dirty (see the last page of Troubleshooting). Clean the video heads using the Sony T- 25CLD, E-25CLDR, or T-25CLW video head cleaning cassette. If these cleaning cassettes are not available in your area, have the heads cleaned at your nearest Sony service facility (a standard service charge will be required). Do not use a commercially available liquid type cleaning cassette other than Sony’s, as it may damage the video heads. • The video heads may have to be replaced. Consult your local Sony service facility for more information. The picture rolls vertically during picture search. • Adjust the vertical hold control on the TV or monitor. Troubleshooting Symptom Remedy Playback The picture has no sound. • Thetapeisdefective. • If you made A/V connections, check the audio cable connection. The sound is unstable or has an echo. • When you play a tape with the same sound recorded on both the hi-fi and normal audio tracks, make sure AUDIO MIX in the OPTIONS-1 menu is set to OFF. The sound from a tape recorded with the VCR is notinstereoor the STEREO indicator in the display window is flashing. • Adjust the tracking. • The video heads are dirty. Clean the video heads using the Sony T-25CLD, E-25CLDR, or T-25CLW video head cleaning cassette as explained above. Recording No TV programme appears on the TV screen. • Make sure the TV is set to the video channel. If you are using a monitor, set it to video input. • If your TV is connected to the VCR with both Scart and aerial cables, make sure the RF channel is set to OFF (see page 21). • Existing broadcasts may interfere with the VCR. Reset the RF channel output of your VCR. • Select the correct source with the INPUT SELECT button. Select a programme position when recording TV programmes; select a line input when recording from other equipment. TV reception is poor. • Make sure the aerial cable is connected securely. • Adjust the TV aerial. Thetapestartsplaying as soon as it is inserted. • The safety tab has been removed. To record on this tape, cover the tabhole(seepa...

Baixe o seu

Para fazer o download, introduza 2 dígitos :