Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
• DC/video servo type lenses are not supported. • When "ON" is selected for "Flicker-less mode", sensitivity may be decremented. Configure the settings relating to audio [Audio] Click the [Audio] tab on the "Camera setup" page. ( page 16) The settings relating to audio can be configured on this page. [Mic mode*] Select "ON" or "OFF" to determine whether to turn on or off audio on a PC. ON: Transmits audio from the camera to the PC. Audio can be heard with images on the PC. Images and audio will not be synchronized. OFF: Does not transmit audio from the camera to the PC. Therefore, no settings and controls relating audio will be invalidated. Default: ON [Audio bit rate] Select "16 kbps" or "32 kbps" for audio bit rate. Default: 32 kbps [Audio sensitivity] Select the sensitivity of the built-in microphone of the camera from the following. Low/Middle/High Default: Middle [Transmission interval] Select an interval for audio transmission from the followings. 20 msec/40 msec/80 msec/160 msec Default: 40 msec Note: When a shorter interval is selected, delay time will be shorter. When a longer interval is selected, audio interruption may be diminished even though delay time will be longer. Select the interval according to the network environment. [Authentication] Select an access level for audio transmission from the following. Refer to page 36 for further information about the access level. Level 1only/Level 2 or higher/All users Default: All users Note: Images and audio will not be synchronized. Configure the multi-screen settings [Multi-screen setup] The cameras to be used for the multi-screen display can be registered on this page. Refer to page 16 for descriptions of how to display "Multi-screen setup" page. [IP address] Enter the IP address or the host name of the camera to be used for the multi-screen. 4 cameras can be registered as a group and up to 2 groups (8 cameras) can be registered. When the HTTP port number for the camera had been changed, enter as follows: "IP address of the camera:port number", for example "192. 168. 0. 10:8080". Number of characters for the IP address: 1 - 128 characters Note: When using the host name, it is necessary to configure the DNS settings. ( page 40) [Camera title] The entered camera title will be displayed on a multi- screen. Number of characters for the camera title: 0 - 20 characters Configure the alarm settings [Alarm setup] The settings relating to alarm occurrences such as settings for the alarm action at an alarm occurrence, the alarm occurrence notification, and the VMD area settings can be configured on this page. The "Alarm setup" page has 3 tabs of the [Alarm] tab, the [VMD area] tab and the [Notification] tab. Configure the settings relating to the alarm action [Alarm] Click the [Alarm] tab on the "Alarm setup" page. ( page 16) The settings relating to the alarm action can be configured on this page. Refer to pages 29 and 30 for further information about the settings relating to the alarm image and the alarm out connector. [Originating port number] Select a port number to be used to receive the command alarm. Available port number: 1 - 65535 Default: 8181 [Terminal alarm] Select "ON" or "OFF" to determine whether or not to receive the terminal alarm. Default: OFF [VMD alarm] Select "ON" or "OFF" to determine whether or not to perform the alarm action using the VMD function. Refer to page 31 for descriptions of how to set the VMD areas. Default: OFF [Command alarm] Select "ON" or "OFF" to determine whether or not to receive the command alarm. The command alarm is the function that notifies of Panasonic protocol alarm from the other cameras. When "ON" is selected, alarm actions will be performed between multiple cameras. Default: OFF Configure the settings relating to the alarm image [Alarm image setup] Click the [Alarm] tab on the "Alarm setup" page. ( page 16) The settings relating to the alarm image to be transmitted to the FTP server can be configured on this page. The alarm image will be transmitted to the FTP server. To transmit alarm images to the FTP server, it is necessary to configure the settings in advance. ( page 38) Refer to pages 29 and 30 for further information about the settings relating to the alarm image and the alarm out connector. Important: Depending on the network line speed or the network traffic, images may not be transmitted at the exact designated interval or period. [Alarm image FTP transmission] Select "ON" or "OFF" to determine whether or not to transmit the alarm image to the FTP server. Default: OFF [Directory] Enter the directory name where the alarm images are to be saved. For example, enter "/ALARM" to designate the directory "ALARM" under the FTP root directory. Number of characters for the directory name: 0 - 256 characters [File name] Enter the file name used for the alarm image to be transmitted to the FTP server. The file name will be as follows. ["Entered file name" + "Time and date (year/month/day/ hour/minute/second)"]...