Using this option you can control whether the unit monitors the vehicle’s glow plug circuit using the Pink input wire (Default), or you may select a specific delay time Before cranking. This option is helpful if you are unable to locate a glow plug signal. Just select a delay time and do not connect the Pink Glow Plug wire. Selections: 10, 20, 30 seconds, or Monitor Pink Wire (Default). 23. REMOTE START ENGINE RUN TIME: Set engine run time for 12, 24, 36 or 48 minutes as desired. 24. ULTRA-SMART

2 Installation Caution and Warnings ............................................................................................... 3 Control Module and Components ............................................................................................. 3-4 Mounting Location………………………………………..................................................................4-5 Installations...........................................................................................................................

Driver’s Side Under dash mounting provides an easy location for wiring most of the system’s connections, however this is a common location for an intruder to check for an alarm after breaking into the vehicle. SIREN: Mount the siren under the hood to an inner fender-well, wheel-well, or other body surface with the open end facing downward. Run the red siren wire through the firewall using a rubber grommet. Ground the sirens black wire to metal near the siren or you can use one of the siren’s mou

Some require the addition of a relay, diode or other component to function properly, which is not Additional labor and parts will be required for some vehicle with Anti-Theft Systems such as GM PassKey/Passlock/VATS, or Key-FOB based Transponder systems. This system is designed for single vehicle operation Technical support is available from the following TECHNICAL SUPPORT (800)-998-6880 Monday - Friday 8:00am - 4:30pm Pacific Fax-On-Demand 805-526-9540 Web Site: E-mail: tech-support@crimestoppe

The holder accepts a 1/ 4-inch striped stranded wire. Tighten the fuse holder ends by securely tightening by hand. *Improper connection could result in numerous “Start up test” notifications, and increased usage on monthly billing. Powering the Unit for the First Time *Disconnect the backup battery if it is installed. Connect the two coax cables from the combo antenna (securely) and connect the vehicle’s 12-volt power and observe the LED on the Module. During the initial 15 minutes after +12 vol

Use the TACH FINDER feature if needed. TACH FINDER FEATURE: The Tach Finder mode can assist you in locating or verifying a Tach source for your installation. Follow the Tach Finder steps below to locate signal. The unit will begin to flash the parking lights if you have the White/Red wire connected to a valid tach source. If lights do not flash, then try another wire until you locate a tach signal that will cause the Parking lights to flash. NOTE: On vehicles equipped with daytime running lights

This system is the most advanced and reliable Remote Start system available on the market today. This booklet contains the information necessary for using & maintaining your remote start system. If any questions arise, contact your installation dealer or Crimestopper Security Products Inc. at (800) 998-6880. *IMPORTANT INFORMATION-MODEL RS901* When RS901 remote starter is activated by an ALARM SYSTEM REMOTE CHANNEL OUTPUT, or a FACTORY KEYLESS ENTRY SYSTEM the following features may not be avail

If the system is armed, pressing Button 4 may or may not trip the alarm system when opening the trunk depending on programming option #7. See page 8. 12 OPERATING INSTRUCTIONS EMERGENCY OVERRIDE & DISARM If you have lost the transmitter or it stops working for any reason and the Alarm is armed, you will have to perform and Emergency Override to Disarm the Alarm. Open the door with the key, (alarm will sound). Turn the ignition on and press the override/program button 4-5 seconds (until siren sto

DISARMING BUTTON 2 BUTTON 1 BUTTON 1 + 2 = BUTTON 4 (NO BUTTON 3 WITH WATCH) To disarm the alarm and unlock the doors, press the #2 Button on either transmitter. You will hear 2 siren chirps and the lights will flash twice. The in-dash LED stops flashing dome light turns on. (Optional) If the alarm is tripped, then the #2 Button will have to be pressed twice. The first press will reset the trigger and the second press will Disarm. OPERATION OPERATION ALARM CYCLE RESET If and when the alarm syste