Assessments - 3, GPA: 5 ( )

Fabricante : Desa Arquivo Tamanho: 4.93 mb Arquivo Nome : Língua de Ensino:

Flames contacting logs will create soot. Each log is marked with a number. These numbers will help you identify the log when installing. It is very important to install these logs exactly as instructed. Do not modify logs. Only use logs supplied with heater. 1. Place the front log (#1) on the grate fingers. Make sure the front log rests firmly between the grate fingers and the grate base (see Figure 24). Figure 24 - Installing Front Log #1 (CCL3930PTB/NTB Shown) Front Log (#1) Grate Fingers Grate Base INSTALLATION Continued Figure 21 - Installing Middle Log (#2) Figure 22 - Installing Front Log (#3) Figure 23 - Installing Crossover Log (#4) Burner Notches Crossover Log (#4) Rectangular Knobs Cutout Tab U-Shaped Slot Middle Log (#2) “U” Bend 3 Front Log (#3) Post Post Recess 3. Locate the recesses on the back of the front log (#3). Fit these recesses between the posts of the grate base (see Figure 22). 4. Locate the notches in the bottom of the crossover log (#4). Place the crossover log on top of the middle log and front log. Make sure the notches of the crossover log lines up with rectangular knobs on top of the middle and front logs (see Figure 23). 5. Place lava rock around base of heater if desired. Do not put lava rock on logs on burner. INSTALLATION Installing Logs (Cont.) Figure 20 - Installing Back Log (#1) Pin Hole in Grate Base Back Log (#1) Burner 111160-01B Forr morre iinfforrmattiion,, viisiitt 1155 INSTALLATION Continued Figure 25 - Installing Middle Log #2 (CCL3930PTB/NTB Shown) Figure 26 - Installing Rear Log #3 (CCL3930PTB/NTB Shown) Figure 27 - Installing Crossover Log #4 (CCL3930PTB/NTB Shown) Middle Log (#2) Tab Burner U-Shaped Slot Hole in Grate Base Pins Burner Middle Log (#2) Back Log (#3) Pins Crossover Log (#4) INSTALLATION Installing Logs (Cont.) 2. Place the base of the middle log (#2) in the U-shaped slots of the grate base. The cutout on the right of the middle log should fit over the burner (see Figure 25). Make sure the front of the middle log is resting on the tabs of the grate base. 3. Locate pins on the bottom of back log (#3). Slide these pins into the holes in the grate base behind the burner (see Figure 26). 4. Locate holes on the bottom of crossover log (#4). Slide front hole onto the left pin (CCL3924PTA/NTA or CCL3930PTB/ NTB) or middle pin (CCL3018PA/NA or CCL3018PTA/NTA) on the middle log (#2) and the pin on the back log (#3). See Figure 27 for placement. 5. For CCL3924PTA/NTA and CCL3930PTB/NTB Only: Locate pin and hole on the bottom of crossover log (#5). Slide the pin into the hole located in crossover log (#4). Slide the hole onto the pin on front log (#1). See Figure 28. For CCL3018PA/NA and CCL3018PTA/NTA Only: Locate holes on the bottom of crossover log (#5). Slide the holes over the left pins on middle log (#2) and front log (#1). See Figure 29. Figure 28 - Installing Crossover Log #5 (CCL3930PTB/NTB Shown) Crossover Log (#4) Front Log (#1) Crossover Log (#4) Front Log (#1) Figure 29 - Installing Crossover Log #5 and Log #6 (CCL3018PA/NA and CCL3018PTA/NTA Only) Crossover Log (#5) Crossover Log (#5) Rear Log (#3) Middle Log (#2) Crossover Log (#6) 111160-01B Forr morre iinfforrmattiion,, viisiitt 16 Single Burner Seasonal Oak Models CRL2718P/N, CRL2718P/N WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury. The Seasonal Oak Log Set is a reversible log set. This means that the two bottom logs may be turned to face either direction. The top log, however, must remain in the same position. Do not modify logs. Only use logs supplied with heater. 1. Place the back log onto the back of the base assembly. Make sure log sits forward against the two posts in front of log (see Figure 32). This log may be turned to face either direction. 2. Place front log onto grate on front of base assembly. The log will fit down between grate fingers and posts on front of base assembly (see Figure 33, page 17). This log may be turned to face either direction. 3. Place the crossover log on top of the back log and front log making sure pins are inserted into holes on top of logs 1 and 2 (see Figure 34, page 17). This log must be placed as shown in Figure 34 on page 17 or the pins will not seat into holes. 4. Add lava rock around base of heater if desired. Do not put lava rock on logs or burner. Figure 32 - Installing Back Log Back Log Post Post Base Assembly INSTALLATION Continued 7 6 Figure 30 - Installing Crossover Log #6 (CCL3930PTB/NTB Shown) Figure 31 - Installing Crossover Log #7 (Model CCL3930PTB/ NTB Only) Pins Middle Log (#2) Front Log (#1) Middle Log (#2) Crossover Log (#6) Holes Pins INSTALLATION Installing Logs (Cont.) 6. Locate holes on the bottom of crossover log (#6). Slide these holes onto the right pins located in middle log (#2) and front log (#1). See Figure 30 for CCL3924PTA/NTA or CCL3930PT...

Baixe o seu

Para fazer o download, introduza 2 dígitos :