Assessments - 2, GPA: 5 ( )

Fabricante : Beverage-Air Arquivo Tamanho: 230.98 kb Arquivo Nome : 8fe328f7-77f2-d434-e112-007c9e688670.pdf Língua de Ensino:

Installation Your Refrigerator Needs Air For correct operation this appliance must be located in a dry atmosphere, away from heat sources, e.g. cookers, radiators, boilers and direct sunlight. You should also ensure that air can circulate freely around the back and the top of the cabinet. There should be 100mm (4”) between the top of the cabinet and any overhanging kitchen furniture. Alternatively allow 50mm (2”) between the top of the cabinet and any overhanging kitchen furniture and a gap of 25mm (1”) on either side of the appliance. If your refrigerator is installed under a continuous worktop, an air outlet opening of at least 200 cm2 and a ventilation grille (A/B) matching the worktop design should be installed at the rear of the worktop. The cut surfaces of the worktop (C) should be varnished to avoid swelling due to penetration of moisture. The appliance wall distance must beat least 30 mm and should be checked before the ventilation grille is inserted. Detaching the Worktop After the worktop has been removed the appliance can be installed underneath a continuous worktop. The procedure is as follows: 1.Unscrew the screws (1) on the right and the left. 2. Lift the worktop slightly, push it about 20 mm towards the rear, and lift it off upwards (2). Unscrew the holding bracket (3) and keep it in a safe place (4). Installation Levelling The appliance must be level. Level the appliance by adjusting the two adjustable feet (1) at the front of the appliance. If required the washer (2) can be removed. 21 Reversing the Door The side at which the door opens can be changed from the right side (as supplied) to the left side, if the installation site requires. Warning! When changing the side at which the door opens, the appliance must not be connected to the mains. Remove plug from the mains beforehand. Carefully tilt the appliance to the back and place an adequate object under it. Take care to avoid the compressor or the condenser touching the ground. Unscrew both adjustable legs at the front. Dismount the door holder at the bottom on the right side. For this, drive the three screws out, and pull the door holder down together with the door holder pin. Remove the screw on the left side, and drive it in on the right side. Remove the door by pulling it downwards while keeping it slightly opened. Unscrew the upper door holder, and screw it in on the opposite side. Installation Put the door back in its place. Relocate the door holder pin in the door holder as per the figure. Place the door holder pin in the door at the bottom on the left side, and fix the door holder with the screw. Drive in the two adjustable front legs, and raise the appliance in the upright position. Relocate the door handle from the left side to the right, and blind the bore-holes with the plugs delivered with the appliance. To reverse the handle proceed as follows: Remove screw covers (if fitted) and handle retaining screws. Remove blanking plugs on the opposite side using a punch. Relocate the handle to the opposite side and refit retaining screws (covers if fitted), and push the plastic plugs supplied with the appliance into the holes where the handle was previously fitted. Plug Socket The plug socket necessary for connection of your appliance to the electricity supply should be positioned so that it is possible to pull out the appliance plug. If your appliance is installed under a continuous worktop, the plug socket should be provided as shown. Alternatively a concealed spur socket fitted with a 13 A fuse may be fitted. If the outlet socket is no longer accessible after installation of the appliance, the electrical installation must include suitable means of isolating the appliance from the mains (e.g. fuse, cut-out, current trip or similar with a minimum contact separation of 3 mm). The mains cable may only be changed by a qualified electrician or competent person. If your appliance needs repairing, please contact your local Service Force Centre. Electrical Connection Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. This appliance must be earthed. The manufacturer declines any liability should these safety measures not be observed. Electrical Requirements Before switching on, make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. The appliance is supplied with a 13 amp plug fitted. In the event of having to change the fuse in the plug supplied, a 13 amp ASTA approved (BS 1362) fuse must be used. Should the plug need to be replaced for any reason. The wires in the mains lead are coloured in accordance with the following code: Green and Yellow: Earth Blue: Neutral Brown: Live The wire coloured green and yellow must be connected to the terminal marked with the letter „E“ or by the earth symbol or coloured green and yellow. The wire coloured blue must be connected to the terminal „N“ or coloured black. The wire coloured brown...

Baixe o seu

Para fazer o download, introduza 2 dígitos :