Assessments - 3, GPA: 4 ( )

Fabricante : Avanti Arquivo Tamanho: 230.98 kb Arquivo Nome : 8fe328f7-77f2-d434-e112-007c9e688670.pdf Língua de Ensino:

Drive in the two adjustable front legs, and raise the appliance in the upright position. Relocate the door handle from the left side to the right, and blind the bore-holes with the plugs delivered with the appliance. To reverse the handle proceed as follows: Remove screw covers (if fitted) and handle retaining screws. Remove blanking plugs on the opposite side using a punch. Relocate the handle to the opposite side and refit retaining screws (covers if fitted), and push the plastic plugs supplied with the appliance into the holes where the handle was previously fitted. Plug Socket The plug socket necessary for connection of your appliance to the electricity supply should be positioned so that it is possible to pull out the appliance plug. If your appliance is installed under a continuous worktop, the plug socket should be provided as shown. Alternatively a concealed spur socket fitted with a 13 A fuse may be fitted. If the outlet socket is no longer accessible after installation of the appliance, the electrical installation must include suitable means of isolating the appliance from the mains (e.g. fuse, cut-out, current trip or similar with a minimum contact separation of 3 mm). The mains cable may only be changed by a qualified electrician or competent person. If your appliance needs repairing, please contact your local Service Force Centre. Electrical Connection Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. This appliance must be earthed. The manufacturer declines any liability should these safety measures not be observed. Electrical Requirements Before switching on, make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. The appliance is supplied with a 13 amp plug fitted. In the event of having to change the fuse in the plug supplied, a 13 amp ASTA approved (BS 1362) fuse must be used. Should the plug need to be replaced for any reason. The wires in the mains lead are coloured in accordance with the following code: Green and Yellow: Earth Blue: Neutral Brown: Live The wire coloured green and yellow must be connected to the terminal marked with the letter „E“ or by the earth symbol or coloured green and yellow. The wire coloured blue must be connected to the terminal „N“ or coloured black. The wire coloured brown must be connected to the terminal marked „L“ or coloured red. Upon completion there must be no cut, or stray strands of wire present and the cord clamp must be secure over the outer sheath. Important!The plug must still be accessible after the appliance has been installed. The appliance should not be connected to the electrical supply by means of an extension cable. In case that the electrical cable has to be replaced, please contact your local Service Force Centre. Warning! A cut off plug inserted into a 13 amp socket is a serious safety (shock) hazard. Ensure that it is disposed of safely. Description of the Appliance View of the Appliance 15161234714891113121056 1. Glass shelf 9. Door gasket 2. Defrost water drain 10. Bottle shelf 3. Salad drawer 11. Egg tray 4. Rating Plate 12. Air circulation 5. Adjustable feet 13. Air vent 6. Butter compartment 14. Condenser 7. Interior Light/Thermostat control 15. Evaporator tray 8. Door shelf 16. Compressor Using the Appliance Before Use Remove all securing tapes. Wash the inside of the appliance with lukewarm water with a little bicarbonate of soda added (5 ml to 0,5 litre of water). Do not use soap or detergent as the smell may linger. Dry the appliance thoroughly. Do not use detergents, abrasive powders, highly perfumed cleaning products, wax polishes or products containing alcohol. To Start the Appliance 1. Allow the appliance to stand for 2 hrs after installation. 2. Plug in the appliance and switch on at the mains supply. 3. Turn the thermostat control to the required setting. A setting of 3 is usually suitable for normal operation (see thermostat control). 4. Leave the appliance for approximately 4 hours for the correct temperature to be reached before placing food inside. Thermostat Control The thermostat control situated inside the refrigerator regulates the temperature of the larder compartment. Thermostat control is marked from 1-5 the higher the number, the colder the setting. Position 0 -Off Position 1 -minimum coldness Position 5 -maximum coldness Switching Off the Appliance To switch off the appliance, turn the temperature regulator to position"0". If the appliance is not going to be used for an extended period: 1. Remove all refrigerated packages. 2. Switch off the appliance by turning the thermostat knob to position"0". 3. Remove the mains plug or switch off or disconnect from the electricity supply. 4. Clean thoroughly (see section: “Cleaning and Care”). 5. Leave the door open to avoid the build up of odours. Interior Accessories Storage Shelves Various glass storage shelves are included with your appliance. The ...

Baixe o seu

Para fazer o download, introduza 2 dígitos :