Assessments - 3, GPA: 4.3 ( )

Fabricante : Samsung Arquivo Tamanho: 2.57 mb Arquivo Nome : Língua de Ensino:

If you do not fix the nut (.)firmly, the bolt (.) may be released. 2) Please adjust the height difference between the doors turning the bolt (.) clockwise( ) or counter clockwise ( ). When you turn clockwise ( ), the door goes up. Adjustment location Adjustment location . WRENCH . NUT . BOLT . NUT . BOLT . WRENCH . BOLT . WRENCH Please open the doors and adjust the doors as follows: 1) Release the nut (.) on the lower hinge until the upper end of the bolt (.). When you release the nut(.), use enclosed hex wrench (.) to turn the bolt(.) a little counterNOTE clockwise. Loosen the nut(.) with your finger. NOTE NOTE . NUT INSTALLATION INSTRUCTIONS CHECKING THE WATER DISPENSER LINE 1) In order to operate the ice maker properly, water pressure of 20~125 psi(0.138~0.862 Mpa) is required. In this range, a 6 oz paper cup can be filled in 10 secs. 2) The water filter removes particles. It does not sterilize or destroy any micro-organisms. 3) If the refrigerator is installed in area with low water pressure (below 20psi), you should install a booster pump to compensate for the low pressure. 4) Ensure the water storage tank inside the refrigerator is filled. push the water dispenser lever until the water runs from the outlet. NOTE Water line installation kit is available at extra cost from your dealer. The refrigerator manufac- turer recommends using a water supply kit containing copper tubing. Connecting to water supply line - Shut off the main water supply line and turn the 1. Cold Water line. Ice maker to the off position. 2. Pipe Clamp. -Locate the nearest cold drinkig water line. 3. Water Line Installation Kit. -Follow the instructions in the ice maker 4. Shut Off Valve. installation kit. -After connecting the water supply with water filter, turn on water supply and flush 4 or more gallons into a bucket to clear the water filter. 30 INSTALLATION OF THE WATER DISPENSER LINE Before You Install the water line • This water line installation is not warranted by the refrigerator or icemaker manufacturer. Follow these instructions carefully to minimize the risk of expensive water damage. • Banging pipes (water banging in the pipes) in house plumbing can cause damage to refrigerator parts and lead to water leakage or flooding. Call a qualified plumber to correct the problem before installing the water supply line to the refrigerator. • To prevent burns and product damage, do not hook up the water line to the hot water line. • If you use your refrigerator before connecting the water line, make sure the”Ice Type” is set to the ICE OFF position. • Do not install the icemaker tubing in areas where temperatures fall below freezing. • When using any electrical device (such as a power drill) during installation, be sure the device is insulated or wired in a manner to prevent electric shock. • All installations must be in a accordance with local plumbing code requirements. Connect the water tube to the refrigerator 1) Slip the compression nut through the provided Refrigerator plastic tubing. Compression Nut comprression fitting. (1/4”) (Provided) 2) Tighten the compression nut onto 1/4” Do not overtighten the compression nut. Compression Fitting NOTE . Using Copper Tubing -Slip the compression nut and ferrule on copper Compression Nut tubing as shown. (1/4”) (Purchased) . Using Plastic Tubing -Insert the molded end of the plastic tubing into the compression fitting. 3) Tighten the compression nut onto the compression fitting. Ferrule (Purchased) (Provided) Copper Tubing (Purchased) Plastic Tubing (Purchased) Household Water Line 4) Turn water on and check for any leakage. Water line must be connected to drinkable water only. Cut off 1/4 inch of the provided plastic tubing squarely to prevent leaks when reconnect. NOTE Install the water filter. The water filter in the extra space behind the vegetable Bin. NOTE 1) As shown, the fixed cap separates from the refrigerator by rotat- ing it counterclockwise. Remove the water filter from the box and put a month indicator sticker on the filter as shown ...

Baixe o seu

Para fazer o download, introduza 2 dígitos :