Assessments - 0, GPA: 4
(
)
)
|
Facilidade de uso
Your docked iPhone or iPod will charge until fully charged. Syncing iPhone and iPod to an iTunes Library on Your Computer 1.Connect the small end of the included Sync Cable to the Sync Jack on the rear of the unit and the other end into a USB port on your computer. 2.Slide the Sync Switch located on the top left of the unit to the ON position. Your iPhone or iPod will begin syncing with your computer. DO NOT disconnect the Sync Cable or move the Sync Switch during sync function. A notice should appear on your computer display when sync is complete and it is safe to disconnect. 3.Gently dock an iPhone or iPod into the left dock on top of the unit (see above). 4.Once sync is complete, return the Sync Switch to the OFF position. NOTE: A docked iPhone/iPod will not charge if the sync cable is not connected to a computer while the Sync Switch is in the ON position Using the iB969 Charging iPad and other Devices Using the USB Ports The iB969 has two additonal USB ports on the bottom of the unit, one quick-charging USB port (left) for iPad and other devices and one standard charging USB port (right) that can charge most USB-compatible devices such as Blackberries, eBook readers, etc., allowing you to charge two additional devices at once. Each port has a USB Mode Switch (A–B) to accomodate the different USB-powered devices. 6 Charging Devices A. position: Will charge iPad and most iPod and iPhone models. B. position: Will charge Sony Reader™, Amazon Kindle™, Barnes & Noble Nook™, Border’s kobo™, Blackberry and other devices. If device does not charge, move USB Mode Switch to A position to see if it charges. If device still does not charge, try unplugging the device from the USB port then reconnecting it. Use this USB port to charge iPad USB switch USB switch Using the iB969 1.Make sure unit is connected to a working power source 2.Connect one end of a USB cable (two are included) to either USB port on the bottom of the iB969 and the other into the USB port on your device (see page 2 to match cables with devices). If needed, use the included USB converter tip to match your device’s port. 3.If needed, slide out the rubberized rest to fit your device. 4. Monitor your device’s battery indicator to confirm the device is charging. If the device is NOT charging, try moving the USB Mode Switch to a different position. If the device still does not charge, try unplugging the device from the USB port then reconnecting it For E-readers, extend sliding rubberized rest Rest area for Blackberries or other devices Using the iB969 To charge your iPad, 1. Connect your USB - 30 pin cable to the left USB port and move the USB mode switch for that port to the “A” position before placing your iPad in the iPad rest. 2. Place your iPad in the iPad rest as shown. 3. Connect the 30-Pin plug to the 30-Pin jack on the bottom of your iPad as shown. Place iPad in iPad rest Connect the 30-Pin plug Consumer Product Safety Guide When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in these instructions and on the unit. 1. Water and Moisture – The unit should not be used near water. For example: near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. 2. Ventilation – The unit should be situated so that its location or position does not interfere with its proper ventilation. For example, it should not be situated on a bed, sofa, rug or similar surface that may block ventilation openings. Also, it should not be placed in a built-in installation, such as a bookcase or cabinet, which may impede the flow of air through the ventilation openings. 3. Heat – The unit should be situated away from heat sources such as radiators, heat registers, stoves or other appliances (including amplifiers) that produce heat. 4. Power Sources – The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. 5. Power-Cable Protection – Power supply cables should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. It is always best to have a clear area from where the cable exits the unit to where it is plugged into an AC socket. 6. Cleaning – The unit should be cleaned only using a warm damp cloth. Do not use solvents, etc. 7. Objects and Liquid Entry – Care should be taken so that objects do not fall and liquids are not spilled into any openings or vents located on the product. 8. Attachments – Do not use attachments not recommended by the product manufacturer. 9. Lightning and Power Surge Protection – Unplug the unit from the wall socket and disconnect the antenna or cable system during a lightning sto...